background image

                                                                               

BKS-ST-180C_Product Manual

 

BooCax 

 

3

  / 

28

 

boocax.com 

1.

 

Introduction to Spray Robot 

 

 

 

 

   

 

 

 

 

 

 

 

 

Product Features 

 

The spray volume is up to 2600 ml/h, with the atomized particles less than 10 microns; 

 

The spray diameter is 5

6 m, leaving no dead corners in the spraying area; 

 

16 L large-capacity tank covers a spraying area up to 20000

 

It is simple to use with mobile App control and supports two spraying modes: regular spraying, 

immediate spraying; 

 

It can automatically detect the obstacles without manual monitoring, thus reducing the burden 

on personnel; 

 

The autonomous navigation function enables a full coverage of the spraying area; 

 

With 4.5 hours of battery life, repeated charging is not needed; 

 

Automatic return for charging spares the trouble of artificial assistance for charging; 

 

When the liquid is lower than the warning level, the robot will automatically close the spray 

device and returns to the charging pile. 

 

 

 

 

 

BooCax  BKS-ST-180C  atomizing  spray  robot  is 

designed to purify the air by rapidly atomizing the liquid 
and automatically spraying the area.   

This robot can automatically navigate to the area for 

full-coverage spraying, and supports mobile App control to 
achieve man-machine separation and minimize personnel 
exposure, so that the use safety is greatly improved. With 
simple structure, it is easy to maintain and manage. 

The  spray  robot  is  widely  applicable  to  hospitals, 

airports, office buildings, shopping malls, schools, factories 
and other public places. 

Summary of Contents for BKS-ST-180C





























Reviews: