The fixings supplied with the 5001 are the same as a
normal 5000 plus the following; 2×off-set spindle (1
right handed & 1 left handed),1 strike plate, 1 box
keep,
1
60mm tubular latch &
1
brass support post.
For correct installation you will need to read the
following instructions carefully.
1. Mortise a hole (30 mm diameter 85mm deep) in
the edge of the door to take the tubular latch.
2. With the hole drilled, you will need to check that the
latch will slide in and out freely and operate wihtout
catching on the inside of the hole. Then you will
need to mark out the size of the faceplate on the
door, use a Stanley knife to do this to avoid splitting
when you chisel out a rebate to make the faceplate
flush with the door edge.
3. You will now need to drill the two small holes that will
accommodate the fixing posts and screws. Also you
will need to drill a hole to slot the spindle though. it
is very important the holes are in line, as
mis alignment will cause the lock to malfunction or
even break up within a very short period. So please
take care to align these locks very carefully. To stop
the splitting and make the holes more accurate you
should drill the holes from both sides (not all the
way through)
4. The most important part of installing this lock is to
make sure that you have selected the correct
spindle. If uncertain, please refer to the handing
chart provided. Once you have the correct spindle,
you should assembly and install the spindle as
described earlier in this manual. At this point, you
should also screw in the brass support post. As this
part helps to keep the alignment of the unit and
latch once the unit has been installed. (You should
now follow the final installation instruction on page 2)
For any further detlils or information about you lock
please call the Borg Helpline on 0800 44 88 377
OTHER LOCKCASES
The 5000 can be fitted with other makes of
locks and lockcases, and we can provide special fixings
pack where necessary.
For more information and advice, please call our
help ine number.
l
5. Now replace the covering panel and hand tighten
6. The code has now been changed, please check to
see that it is working correctly, also make a note
of the code for future reference. Once satisfied
that the lock is working as normal you are ready to
fit/re-fit the lock.
NOTES ABOUT THE CODE
You will have been provided with 4 spare tumblers
( 2 red and 2 blue ) these are to shorten or lengthen
your code.
N. B Your code can be entered in any order or
sequence e. g. 1234 or 4321 or 2431. There
are over 1,000 different combinations
avallable.
The button activates the code free entry feature, so if
1. Firstly, you will need to check that the original
2.
3.
Turn the keypad over and remove the 4 red
screws.
You will now be able to lift off the covering panel (
please be careful as there are 12 springs attached
to this panel). Please note that the red tumblers
will relate to the code printed on the card
provided.
Also note that the C tumbler is un
-
coloured and is NOT to be removed.
4. To change your code you will now need to hold
the keypad face down,
Next depress & hold the C
tumbler ( if this is not done you may damage
some of the internal components.)
Now using the
tweezers provided, you can reposition the
tumblers to the code you want ( red tumblers are
coded and blue tumblers are uncoded). Please
ensure that the space cut-out on each tumbler is
facing the outside of the lock body, also make
sure that the coloured mark is facing upwards.
If
any one tumbler is upside down or the wrong way
round the lock will not work and if forced will
break the internal components.
Please note that
the code must always start with a C.
To change the code on this lock you will need to
follow the instructions below very carefully, as any
mistake may damage or cause the lock to
malfunction.
CODE CHANGING PROCEDURE
5001 INSTALLATION INSTRUCTIONS
you require continuous free passage you will need to
proceed as follows:
If
the function is not required, it can be easily removed
by
unscrewing the 4 red screws on the back of the keypad
to
expose the tumblers. Depress the button and keep
it
depressed, and using the tweezers provided to lift out the
tumbler
. Now replace the metal cover and 4 red screws.
1 .
Enter your access code, but before depressing the
lever press the button.
2.
You will now be able to rotate the handle freely
without entering the code.
3.
To cancel the free entry feature, press the button
followed by the button and this will reset the unit.
F
F
F
F
F
C
C
Square
cut-out
Red Coded
Tumbler
Buttons
Square
cut-out
Square
cut-out
Outwards
Square
cut-out
Blue Non-Coded
Tumbler
Outwards
