Bort 91275752, Installation Instructions Manual

10

NOTE: It may be necessary to expand the drain 
hole for installation lange fastening disposer. 
Equipment for extending the drainage hole is 
purchased separately. 

3. DISASSEMBLY OF THE ASSEMBLY UNIT

• Turn over the assembly (Fig.4.1) and loosen the 
three ixing screws (1) The access to the ring (2). 
• Disconnect the retaining ring from the lange 
with a screwdriver. Now the assembly unit can be 
disassembled. 

4. ATTACHING THE FIXING ASSEMBLY TO WASH-
ING Fig.5.1.

1. Install one or two rubber gaskets (2) under the 
washing lange (1). Make sure that The drainage 
hole is not clogged, and set to lange washer / 
gasket. In order to The lange of the sink became in 
place, you need to crush it with a heavy load. (To 
avoid scratches, use a towel as a lining.) 
2. Put the second rubber part on the bottom of 
the kitchen sink a gasket (2), a cardboard gasket 
(optional) (3) and a metal support ring (4) (lat side 
up). 
3. While holding the second rubber gasket, 
cardboard padding (optional) and a metal support 
ring, put the mounting ring (5) on the lange of the 
sink so that it aligned with the support ring. 
4. Pressing tightly to the bottom of the sink 
rubber gasket, cardboard gasket, support ring and 
mounting ring, slide the snap ring (7) onto the 
lange of the sink so that it snaps into the lange 
groove. 
5. Tighten the three ixing screws (6) to The ixing 
assembly was tight and evenly pressed to the sink. 

5. CLEANING THE DRAIN PIPE 

If you do not clean the drain pipe, it can clog. 
1. Remove the water trap. (Fig.6.1) 
2. Using a cleaner, remove all solid precipitation in 
the horizontal part of the drainage pipes, moving 
with side of the siphon towards the main pipe. 
IF THE DISHWASHER WILL NOT BE CONNECTED TO 
THE DISPOSER, GO TO PART 7 OF THIS INSTRUCTION 

6. CONNECTING THE DISHWASHER MACHINES 
AND TRANSFER CONNECTION

If the sink is full of liquid it can be discharged into 
the disposer through the inlet in its upper parts. 
(Fig. 7.2)
On all models inside the intake pipe there is 
partition. The partition must be removed (Fig. 7.1).

REMOVING THE PLATE / PARTITION

1. Place the disposer on one side and place it 
screwdriver into the connection for the dishwasher, 
pushing it until it will not rest against the partition 

in the end of the branch pipe.
2. With several blows of the hammer, knock out the 
septum in the branch pipe (Fig. 7.1).
3. Remove the embossed partition from the disposer 
bowl. If necessary to connect the dishwasher, then 
it should be connected to the inlet of the overlow 
outlet pipes To connect to the overlow inlet, 
remove the exhaust pipe cover by unscrewing the 
cover (Fig. 7.3).

7. CONNECTING THE DISPOSER TO THE FIXING 
UNIT ATTENTION! 

To avoid injury, follow the so that during the 
removal and installation of a part Your body was 
not under the disposer; during the installation it is 
possible to drop it.
Remove any objects from the grinding chamber 
product before installing it on the sink. 
1. Install the product in such a way that provide 
easy access to the restart button engine located in 
the lower part of the body. Do not block this place 
with any objects. 
2. Place the disposer with three mounting loops 
(1) into the sliding position by mounting rails (2). 
(Fig.8.1) 
3. Lift the disposer, insert the top end (installation 
gasket) in the mounting and turn the setting ring to 
the right (with a wrench or adjustable pliers) until 
the mounting loops are ixed (3) with respect to the 
mounting rails (Fig. 8.2). 
Make sure that all three mounting loops are locked. 
Disposer is installed. 
4. Run water into the sink, then check the 
connections for leaks. 
5. Insert the noise absorbing screen into the drain 
hole lat side up. (Fig.8.3) 

8. CONNECTING THE OUTLET PIPE

To the DRAIN PIPE ATTENTION! 
• It is recommended to wear protective goggles 
when installing the disposer. 
• For all models, the drain pipe is connected using a 
screw connection (Fig. 9.2). 
• Use a sanitary sealant only for connecting the 
lange of the sink with the disposer. 
Do not use sealants for threaded pipe connections 
or anaerobic screwed sealants. They can damage 
the product. 
• Regularly check the disposer and ittings for 
water leaks, since leaks water can cause damage to 
property. 
The manufacturer is not responsible for damage to 
property as a result of water leaks. 

INSTALLING THE DRAINAGE SYSTEM