Bort 98291476, User Manual

6

Angle grinder

INTENDED USE

This tool is intended for grinding, cutting and deburring 
metal and stone materials without the use of water; with 
the appropriate accessories the tool can also be used for 
brushing and sanding

TECHNICAL SPECIFICATIONS  

 1 

PRODUCT ELEMENTS 

 2 

1. 

Spindle

2.

 Clamping 

fl

 ange

3.

 Spanner

4.

 Spindle-lock button

5.

 Auxiliary handle

6.

 Safety guard

7.

 Mounting 

fl

 ange

8.

 On/off locking switch

9. 

Switch-lock knob

SAFETY

WARNING!  Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, 

fi

 re 

and/or serious injury. 

●

  Only use this tool for dry grinding/cutting

●

  Only use the 

fl

 anges which are supplied with this tool

●

  This tool should not be used by people under the age of 

16 years

●

 Always disconnect plug from power source before 

making any adjustment or changing any accessory

ACCESSORIES

●

 Use the original SBM Group accessories which can be 

obtained from your SBM Group dealer

●

 For mounting/using non- SBM Group accessories ob-

serve the instructions of the manufacturer concerned

●

  Use only accessories with an allowable speed matching 

at least the highest no-load speed of the tool

●

 Do not use damaged, deformed or vibrating grinding/ 

cutting discs

●

 Handle and store grinding/cutting discs carefully to 

avoid chipping and cracking

●

  Protect accessories from impact, shock and grease

●

  Do not use a grinding/cutting disc that is larger than the 

maximum recommended size

●

 Only use grinding/cutting discs with a hole diameter 

which 

fi

 ts  mounting 

fl

 ange (7) without play; never use 

reducers or adaptors to 

fi

 t large-hole grinding/cutting 

discs

●

 Never use grinding/cutting discs with a threaded hole, 

of which the thread is not long enough to accept the spin-
dle length of the tool

●

 Never use accessories with a “blind” threaded hole 

smaller than M14 x 21 mm

OUTDOOR USE

●

 Connect the tool via a fault current (FI) circuit breaker 

with a triggering current of 30 mA maximum

●

 Only use an extension cord which is intended for out-

door use and equipped with a splashproof coupling-sock-
et

BEFORE USE

●

  Before using the tool for the 

fi

 rst time, it is recommend-

ed to receive practical information

●

  Do not work materials containing asbestos (asbestos is 

considered carcinogenic)

●

 Take protective measures when during work dust can 

develop that is harmful to one’s health, combustible or ex-
plosive (some dusts are considered carcinogenic); wear a 
dust mask and work with dust/chip extraction when con-
nectable

●

 Be careful of hidden electrical wires or gas- and water 

pipes; check the work area, for instance with a metal de-
tector

●

 Be careful when cutting grooves, especially in support-

ing walls (slots in supporting walls are subject to country- 
speci

fi

 c regulations; these regulations are to be observed 

under all circumstances)

●

 Clamp the workpiece in case it does not remain 

stationa ry from its own weight

●

  Do not clamp the tool in a vice

●

 Use completely unrolled and safe extension cords with 

a capacity of 16 Amps (UK 13 Amps)

●

  Wear protective glasses and gloves, hearing protection 

and sturdy shoes; when necessary, also wear an apron

●

  Always mount auxiliary handle (5) and protective guard 

(6); never use the tool without them

●

  Be sure tool is switched off when plugging in 

DURING USE

●

 Always keep the cord away from moving parts of the 

tool; direct the cord to the rear, away from the tool

●

  If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug; 
never use the tool with a damaged cord

●

 Push spindle-lock button (4) only when spindle (1) is at 

a standstill

●

  Keep hands away from rotating accessories

●

  When grinding metal, sparks are generated; keep other 

persons and combustible material from work area

●

  In case of electrical or mechanical malfunction, immedi-

ately switch off the tool and disconnect the plug

●

 In case the cutting disc is blocked, resulting in jerking 

forces on the tool, immediately switch off the tool

●

 In case of current interruption or when the plug is ac-

cidentally pulled out, unlock the on/off switch (8) imme-
diately and put it in the OFF-position in order to prevent 
uncontrolled restarting

●

  Do not apply so much pressure on the tool that it comes 

to a standstill

AFTER USE

●

 Before you put down the tool, switch off the motor and 

ensure that all moving parts have come to a complete 
standstill

●

  After switching off the tool, never stop the rotation of the 

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

●

 Do not connect the blue (= neutral) or brown (= live) 

wire in the cord of this tool to the earth terminal of the 
plug

English