Bort 98298680, User Manual

6

Cordless rotary hammer

INTENDED USE

•  This tool is intended for hammer drilling in concrete, brick 
and stone; for drilling in wood, metal and plastic as well as for 
screwdriving (speci

fi

 c accessories should be used)

•  The hammering system in this tool outperforms any tradi-
tional ratcheting drill when drilling in concrete
• This tool is designed for use in combination with all standard 
SDS+ accessories

TECHNICAL SPECIFICATIONS 

 1 

PRODUCT ELEMENTS  

 2 

1 

On/Off switch

2 

Switch for changing direction of rotation

3 

Switch for selecting operating mode

4 

Locking sleeve

SAFETY

WARNING!  Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, 

fi

 re and/

or serious injury. 

• Ensure the switch is in the off position before inserting 
battery pack. Inserting the battery pack into power tools 
that have the switch on invites accidents.
• Recharge only with the charger speci

fi

 ed by the manufac-

turer. A charger that is suitable for one type of battery pack may 
create a risk of 

fi

 re when used with another battery pack.

• Use power tools only with speci

fi

 cally designated battery 

packs. Use of any other battery packs may create a risk of 
injury and 

fi

 re.

•   Avoid damage that can be caused by screws, nails and 
other elements in your workpiece; remove them before you 
start working
•   Always check that the supply voltage is the same as the 
voltage indicated on the nameplate of the charger (charg-
ers with a rating of 230V or 240V can also be connected 
to a 220V supply)
•   In case of electrical or mechanical malfunction, immediately 
switch off the tool or unplug charger from power source
•   SBM Group can assure 

fl

 awless functioning of the tool 

only when original accessories are used
•   Use only accessories with an allowable speed matching 
at least the highest no-load speed of the tool
•   This tool should not be used by people under the age 
of 16 years
•   Be careful not to drill or drive into areas where electrical 
wires may be contacted
•   Ensure that switch (2) is in the middle (locking) position 
before making any adjustments or changing accessories 
as well as when carrying or storing the tool
•   Do not touch the contacts in the charger
•   Do not expose tool/charger/battery to rain
•   Never charge battery outdoors
•   Store tool/charger/battery in locations where tempera-
ture will not exceed 40° C or drop below 0° C
•   Batteries will explode in 

fi

 re, so do not burn battery for 

any reason
•   When damaged, and under extreme usage and tem-
perature conditions, batteries may start to leak
-    if liquid comes into contact with the skin, wash quickly 
with soap and water, then with lemon juice or vinegar
-    if liquid gets into the eyes, 

fl

 ush eyes with clean water 

for a minimum of 10 minutes and seek immediately medi-

cal attention
•   When battery is not in tool or charger, it should be kept 
away from metal objects such as nails, screws, keys etc. to 
prevent short-circuit
•   Do not use charger when damaged; take it to one of 
the of

fi

 cially registered SBM Group Service Stations for a 

safety check
•   Do not use battery when damaged; it should be replaced 
immediately
•   Do not disassemble charger or battery
•   Do not attempt to recharge non-rechargeable batteries 
with the charger
•  Normally when starting to charge the discharged battery, 
red and green LEDs of the battery charger are on. When the 
battery is fully charged only green LED is on. If no LEDs are 
on while the charger is on, do not use the battery and the 
charger and take them to the service center. 
•   When using your tool continuously, the batteries in your 
battery pack will become hot. You should let a hot battery 
pack cool down for approximately 30 minutes before at-
tempting to recharge.
•   In case of long storage, store the battery in fully charged 
condition. 
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•   Do not connect the blue (= neutral) or brown (= live) wire 
in the cord of the charger to the earth terminal of the plug
•   If for any reason the old plug is cut off the cord of the charger, 
it must be disposed of safely and not left unattended

To ensure longer service life and proper perfor-
mance of the battery, take the following actions 
when you start using new battery: 

1. Use the new battery, without recharging it, till its com-
plete discharge. 
2. Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to 
reach the nominal battery capacity.

MAINTENANCE

Regularly clean the machine housing with a soft cloth, pref-
erably after each use. Keep the ventilation slots free from 
dust and dirt.If the dirt does not come off use a soft cloth 
moistened with soapy water. Never use solvents such as 
petrol, alcohol, ammonia water, etc. These solvents may 
damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during trans-
port, it is delivered in a sturdy packaging. Most of the pack-
aging materials can be recycled. Take these materials to 
the appropriate recycling locations. Take your unwanted 
machines to your local SBM Group dealer. Here they will 
be disposed of in an environmentally safe way.
Li-Ion batteries can be recycled. Deliver them to a disposal 
site for chemical waste so that they can be recycled or dis-
posed of in an environmentally friendly manner.

Make sure that the machine is not live when 
carrying out maintenance work on the motor.