English |
5
Bosch Power Tools
1 609 92A 37Z | (19.10.16)
Safety Warnings for Nibblers
The power tool is not suitable for stationary operation.
For example, it may not be clamped in a vice or fastened on
a workbench.
Wear protective gloves while working and pay particu-
lar attention to the mains cable.
Sharp burrs develop at
the cut steel sheet and can cause injuries to the operator or
damage the mains cable.
Secure the workpiece.
A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Products sold in GB only:
Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only:
Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for cutting sheet metal without de-
forming the material and is suitable for straight cuts, cut-outs
and narrow curves.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1
On/Off switch
2
Screwed cap for die
3
Locking screw for die
4
Die
5
Punch
6
Hollow screw for fastening of punch
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To
start
the machine, push the On/Off switch
1
forward so
that the
“I”
is indicated on the switch.
To
switch off
the machine, push the On/Off switch
1
toward
the rear so that the
“0”
is indicated on the switch.
Locking/Loosening the Die
For straight cuts, tighten the locking screw
3
using an hex key
(size 2.5 mm) in order to lock the die
4
.
For curved cuts, loosen the locking screw
3
. The die
4
can
move freely now and adjusts to the direction of the feed
strength.
Working Advice
Before any work on the machine itself, pull the mains
plug.
Wear protective gloves while working and pay particu-
lar attention to the mains cable.
Sharp burrs develop at
the cut steel sheet and can cause injuries to the operator or
damage the mains cable.
Exercise caution when handling the cutting chips.
The
chips have sharp tips that can cause injuries.
Apply the machine to the workpiece only when switched on.
Always hold the machine vertical to the surface of the steel
sheet and do not tilt it.
The cut takes place during the upward motion of the punch.
Guide the machine evenly and with moderate feed in the cut-
ting direction. A too high feed rate significantly reduces the
service life of the cutting tools and can damage the machine.
Nibbler
GNA 2,0
Article number
0 601 530 1..
Rated power input
W
500
Output power
W
270
Stroke rate at no load n
0
min
-1
2400
Stroke speed under load
min
-1
1500
Max. steel sheet cutting capacity*
mm
2.0
Cutting width
mm
6
Smallest curve radius
mm
3
Weight according to EPTA-
Procedure 01:2014
kg
2.0
Protection class
/
II
* to 400 N/mm
2
with reference to steel sheet
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
OBJ_BUCH-519-002.book Page 5 Wednesday, October 19, 2016 9:56 AM
