12
| English
(15)
Storage compartment locking mechanism
a)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless air pump
UniversalPump 18V
Article number
3 603 J47 1..
Rated voltage
V=
18
Max. output volume
l/min
30
Max. pressure
bar
10.3
psi
150
Weight according to EPTA-Pro-
cedure 01:2014
A)
kg
1.5 (1.5 Ah) to
1.8 (6.0 Ah)
Recommended ambient tem-
perature during charging
°C
0 to +35
Permitted ambient temperature
during operation and during
storage
°C
–10 to +40
Recommended rechargeable
batteries
PBA 18V...W-.
Recommended battery char-
gers
B)
AL 18...
A) Depends on battery in use
B) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
Noise emission values determined according
to
EN 62841‑1
.
Typically, the A-weighted sound pressure level of the power
tool is
78
dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated.
Wear hearing pro-
tection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to
EN 62841‑1
:
a
h
=
1.8
m/s
2
, K =
1.5
m/s
2
.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Rechargeable battery
Bosch
sells some cordless power tools without a re-
chargeable battery. You can tell whether a rechargeable bat-
tery is included with the power tool by looking at the pack-
aging.
Charging the battery
u
Use only the chargers listed in the technical data.
Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note:
Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
u
Do not continue to press the On/Off switch after the
power tool has automatically switched off.
The battery
can be damaged.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out.
Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the state of charge for
a few seconds when the on/off switch is half or fully pressed.
LED
Capacity
3 × continuous green light
75–100 %
2 × continuous green light
40–75 %
1 × continuous green light
15–40 %
1 × slowly flashing green light
0–15 %
The three LEDs in the battery charge indicator and the pres-
sure gauge lighting flash simultaneously when the temperat-
ure of the rechargeable battery is outside the operating tem-
perature range and/or the overload protection has been
triggered.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
1 609 92A 6BC | (09.12.2021)
Bosch Power Tools
