10
| English
Line laser
GLL 3-80 CG
Recommended chargers
GAL 12…
GAX 18…
A) The working range may be reduced by unfavourable environmental conditions (e.g. direct sunlight).
B) At
20–25
°C
C) Applies to the four horizontal intersection points
D) The values stated presuppose normal to favourable environmental conditions (e.g. no vibration, no fog, no smoke, no direct sunlight). Ex-
treme fluctuations in temperature can cause deviations in accuracy.
E) Only non-conductive deposits occur, whereby occasional temporary conductivity caused by condensation is expected.
F) Shorter operating times in
Bluetooth
® operation and/or in conjunction with RM 3
G) When using
Bluetooth®
Low Energy devices, it may not be possible to establish a connection depending on the model and operating system.
Bluetooth®
devices must support the SPP profile.
H) The signal range may vary greatly depending on external conditions, including the receiving device used. The
Bluetooth®
range may be signi-
ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
I)
The lithium-ion battery and the AA1 battery adapter are excluded from IP 54.
Technical data determined using the battery that comes with the product.
The serial number
(18)
on the type plate is used to clearly identify your measuring tool.
Assembly
Measuring Tool Power Supply
The measuring tool can be operated either with conventional
non-rechargeable batteries or with a Bosch lithium-ion bat-
tery.
Operation with Rechargeable Battery
u
Use only the chargers listed in the technical data.
Only
these chargers are matched to the lithium-ion battery of
your measuring tool.
Note:
The use of batteries unsuitable for your measuring tool
can lead to malfunctions or damage to the measuring tool.
Note:
The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". A protective circuit
switches the measuring tool off when the battery is drained.
u
Do not switch the measuring tool back on after it has
been switched off by the protective circuit.
This can
damage the battery.
To
insert
the charged battery
(14)
, slide it into the battery
bay
(9)
until you feel it engage.
To
remove
the battery
(14)
, press the release buttons
(12)
and pull it out of the battery bay
(9)
.
Do not use force to do
this.
Operation with Non-Rechargeable Batteries
It is recommended that you use alkaline manganese batter-
ies to operate the measuring tool.
The batteries are inserted into the battery adapter.
u
The battery adapter is intended only for use in desig-
nated Bosch measuring tools and must not be used
with power tools.
To
insert
the batteries, slide the cover
(10)
of the battery
adapter into the battery bay
(9)
. Place the batteries into the
cover as per the illustration on the sealing cap
(13)
. Slide
the sealing cap over the cover until you feel it click into
place.
To
remove
the batteries
(11)
, press the re-
lease buttons
(12)
of the sealing cap
(13)
and
pull off the sealing cap. Make sure that the bat-
teries do not fall out. To do this, hold the meas-
uring tool with the battery bay
(9)
facing up-
ward. Remove the batteries. To remove the cover
(10)
from
inside the battery bay, reach into the cover and pull it out of
the measuring tool, applying light pressure to the side wall as
you do so.
Always replace all the batteries at the same time. Only use
batteries from the same manufacturer and which have the
same capacity.
u
Take the batteries out of the measuring tool when you
are not using it for a prolonged period of time.
The bat-
teries can corrode and self-discharge during prolonged
storage in the measuring tool.
Battery Charge Indicator
The battery charge indicator
(2)
shows the state of charge of
the battery/batteries:
LED
State of charge
Green continuous light 100–75 %
Yellow continuous light 75–35 %
Red continuous light
35–10 %
No light
– Battery defective
– Batteries drained
If the rechargeable battery or non-rechargeable batteries are
running low, the laser lines will gradually become dimmer.
Immediately replace a faulty rechargeable battery or any
empty batteries.
1 609 92A 5DN | (26.03.2020)
Bosch Power Tools
