10
| English
1 609 92A 0JN | (18.6.14)
Bosch Power Tools
Technical Data
Assembly
Battery Charging (see figure A)
Observe the mains voltage!
The voltage of the power
supply must correspond with the data given on the name-
plate of the battery charger. Battery chargers marked with
230 V can also be operated with 220 V.
The battery is supplied partially charged.
To ensure full battery capacity, completely charge the battery
(at least 2–3 hours) before using for the first time.
The glue pen cannot be used during the charging procedure;
it is not defective, when it does not function during the charg-
ing procedure.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The “Electronic Cell Protection (ECP)” protects the lithium ion
battery against deep discharging. When the battery is dis-
charged, the glue pen is switched off by a protective circuit:
The glue is no longer heated.
– Plug the mains plug of the battery charger into the socket
outlet and the charger plug
9
into socket
8
.
Disconnect the battery charger from the mains supply when
not using it for longer periods.
Protect the battery charger against moisture!
Observe the notes for disposal.
Operation
Starting Operation
Switching On
– To
start the operation
, press the On/Off button
4
until the
LED indicator
5
lights up green.
Switching Off
– To
switch off
, press the On/Off button
4
until the LED indi-
cator
5
goes out.
Automatic shut-off:
Note:
The glue pen switches off automatically after 10 min-
utes in order to save energy.
– Switch the glue pen on again and check the LED indicator
5
.
When the battery LED indicator briefly lights up red, the
battery must be recharged.
To save energy, only switch the glue pen on when you are us-
ing it.
After use, place down the glue pen in a safe manner and
allow it to cool down completely before packing it
away.
The hot nozzle can cause damage and/or burns.
Working Advice
Do not allow the hot glue or the nozzle tip to come into
contact with persons or animals.
Glue and nozzle tip
reach a temperature of approx. 170 °C; danger of burning.
If hot glue comes into contact with the skin, hold the affect-
ed area immediately under a stream of cold water for sev-
eral minutes. Do not try to remove the glue from the skin.
Use only glues recommended by the manufacturer of the glue
pen (see page 3).
Bonded connections can loosen under the effect of moisture.
Cordless glue pen
GluePen
Article number
3 603 BA2 0..
Heating time
s
approx.15
Gluing temperature
°C
approx.170
Glue stick, diameter
mm
Ø 7
Glue stick, length
mm
150
Weight according to
EPTA-Procedure 01/2003
kg
0.1
Battery
Li-Ion
Rated voltage
V=
3.6
Capacity
Ah
1.5
Number of battery cells
1
Operating duration per
battery charge (according to
Bosch testing procedures)
min
approx.30
(corresponds with ap-
prox. 6 glue sticks)
Battery Charger
Article number
2 609 120 4..
Charging time
h
3.0–4.0
Output voltage
V=
5
Charging current
mA
500
Allowable charging
temperature range
°C
+5 ... +40
Weight according to
EPTA-Procedure 01/2003
kg
0.1
Protection class
/
II
LED Indicators
red
green
Meaning
–
The battery is being charged
–
The battery is fully charged
–
The battery has less than 30% of its
capacity and should be charged
–
The battery is completely discharged
Flashing
Continuous light
LED Indicators
green
Meaning
for approx. 15 s
The glue is being heated
Glue pen ready for operation
Flashing
Continuous light
OBJ_BUCH-1693-002.book Page 10 Wednesday, June 18, 2014 1:45 PM
