English |
17
Application
Surface shape
Abrasive tool
Texturing wood
straight
curved
Nylon brush
Abrading paint
(wood)
straight
Sanding sleeve
Conical sanding
sleeve
Flap wheel
(60 mm)
Grinding metal
(e.g. steel, alu-
minium, brass)
straight
Sanding sleeve
Conical sanding
sleeve
Sanding fleece
Flap wheel
(60 mm)
curved
Nylon brush
Cleaning disc
Brass-coated
metal brush
Removing rust
from metals
straight
curved
Cleaning disc
Brass-coated
metal brush
Polishing/texturing
metal
straight
curved
Nylon brush
Sanding fleece
Removing paint
(metal)
straight
Nylon brush
Cleaning disc
Working Advice
The material removal rate and surface quality are primarily
determined by the choice of abrasive tool, the pre-selected
speed setting and the contact pressure.
Only immaculate abrasive tools will deliver good grinding
performance and protect the power tool.
Use only original
Bosch
-sanding accessories.
Preselecting the speed
You can preselect the required speed using the thumbwheel
for speed preselection
(7)
, even during operation.
If the final setting of "6" is reached, the thumbwheel audibly
engages.
1 − 2 low speed
3 − 4 medium speed
5 − 6 high speed
The required speed depends on the material and the work-
ing conditions; it can be ascertained through practical tests.
The figures in the table below are recommended values.
Application
Grit (coarse/fine
sanding)
Speed
setting
Abrading paint
120/240
2/3
Removing paint
80/−
5
Application
Grit (coarse/fine
sanding)
Speed
setting
Softwood
80/240
5/6
Hardwood
80/240
5/6
Veneer
120/240
2 − 4
Aluminium
80/240
4/5
Grinding steel
80/240
3 − 5
Removing rust from
steel
80/20
4 − 6
Stainless steel
80/240
3 − 5
Stone
80/240
5/6
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed
without load for approx. three minutes to cool it down.
Sanding
– Switch the power tool on, place the entire sanding sur-
face against the surface of the workpiece and apply mod-
erate pressure as you move the sander over the work-
piece.
– Be sure to apply consistent contact pressure, in order to
increase the service life of the abrasive tools. An excess-
ive increase of the sanding pressure does not lead to an
increase of the sanding capacity, but to increased wear of
the power tool and the abrasive tool.
– Do not use an abrasive tool for other materials after it has
been used to work on metal.
Maintenance and Service
Maintenance and Cleaning
u
Pull the plug out of the socket before carrying out any
work on the power tool.
u
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by
Bosch
or by an
after-sales service centre that is authorised to repair
Bosch
power tools.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at:
www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Bosch Power Tools
1 609 92A 66Y | (13.01.2021)
Summary of Contents for 4053423225051
Page 3: ... 3 1 Texoro 2 3 4 5 6 7 11 10 9 8 Bosch Power Tools 1 609 92A 66Y 13 01 2021 ...
Page 4: ...4 13 12 10 A B1 B2 1 12 1 10 11 1 609 92A 66Y 13 01 2021 Bosch Power Tools ...
Page 5: ... 5 19 mm 4 15 3 18 D F E 2 16 17 19 C1 C2 14 Bosch Power Tools 1 609 92A 66Y 13 01 2021 ...
Page 202: ...202 1 609 92A 66Y 13 01 2021 Bosch Power Tools ...
