16
| English
1 609 92A 116 | (31.3.15)
Bosch Power Tools
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 60745-1, EN 60745-2-4.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 18.02.2015
Assembly
Battery Charging
Use only the chargers listed in the technical data.
Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note:
The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Removing the battery
To remove the battery
2
, press the unlocking buttons
1
and
pull the battery out of the machine to the rear.
Do not exert
any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4
indicate the charge condition of the battery
2
. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
To indicate the charge condition, press and hold button
3
of
the switched off machine.
Changing the Tool
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Wear protective gloves when changing application
tools/accessories.
Contact with the application tool/ac-
cessory can lead to injuries.
Selecting the Application Tool/Accessory
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
LED
Capacity
Continuous lighting 3 x green
2/3
Continuous lighting 2 x green
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
Accessory
Material
HCS wood seg-
ment saw blade*
Wooden materials,
plastic
BIM segment saw
blade*
Wooden materials,
plastic, non-ferrous
metals
HCS plunge cut
saw blades,
wood*
Wooden materials,
plastic, gypsum
and other soft
materials
BIM plunge cut
saw blades,
metal*
Metal (e. g. unhard-
ened nails, screws,
smaller profiles),
non-ferrous metals
BIM plunge cut
saw blade, wood
and metal*
Wood, metal, non-
ferrous metals
HM-Riff segment
saw blade*
Grouting joints,
soft wall tiles,
glass-fibre reinforc-
es plastic and other
abrasive materials
HM-Riff delta
plate*
Scraper, rigid*
Carpets, coverings
Scraper, flexible* Silicone and other
elastic materials
Base plate for
sanding, series
Delta 93 mm*
Depends on sand-
ing sheet
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
OBJ_BUCH-630-008.book Page 16 Tuesday, March 31, 2015 6:05 PM
