D9068
|
Operation and Installation Guide | 5.0
Programming
.
Bosch Security Systems, Inc. | 3/13 | F01U071094-0
7
45
The Dialing Type determines which
format the D9068 uses for dialing on
each telephone line. Tone/Pulse
attempts tone dialing first, and then
pulse dialing if tone dialing fails.
Monitor Line supervises telephone
line integrity.
Use both telephone lines
(enabled and supervised) for UL
installations.
If Wait DIALTONE is set to
Yes
, the
D9068 starts dialing when it receives
a dial tone. When WAIT DIALTONE is
set to
No
, the D9068 waits 7 sec
before dialing.
3.
Press [1] to select
1: DIALING TYPE
.
The window shows:
DIAL #1 (_____)
1: PULSE ONLY
2: TONE/PULSE
3: TONE ONLY
4.
Press the number key that corresponds
with your selection followed by
[# Command]. Then press [* Clear] to
return to the Line Control submenu.
5.
At the Line Control submenu, press
[2] for
2: MONITOR LINE
. The window
shows:
MONITOR LINE #1
YES: YES (1)/NO (0)
6.
The current selection precedes the
colon (:) on the second line. Press
the number key that corresponds with
your selection.
7.
Press [# Command]. Then press [*
Clear] to return to the Line Control
submenu.
8.
At the Line Control submenu, press
[3] to select
3: WAIT DIALTONE
. The
window shows:
WAIT DIALTONE #1
YES: YES (1)/NO (0)
9.
The current selection precedes the
colon (:) on the second line. Press
the number key that corresponds with
your selection followed by [#
Command]. Then press [* Clear] to
return to the Line Control submenu.
10.Use this same procedure to configure
Line 2.
6: ACK WAIT TIME
To access ACK WAIT TIME, select
[0]: PROGRAM
[5]: PROG ACC’NTS
[6]: ACK WAIT TIME
. After the D9068
dials the telephone number, it waits for
the receiver to answer the telephone and
send the proper handshake tones. If the
handshake is not detected, the D9068
hangs up. This parameter sets the length
of time the D9068 waits before hanging
up.
To set the amount of time the D9068
waits before hanging up:
1.
At the PROG ACC’NTS submenu, press
[6] to select
6: ACK WAIT TIME
. The
window shows:
ACK WAIT TIME (___)
(20-99 SECS):
___
2.
Enter a value between 20 and 99 for
the ACK WAIT TIME and then press
[# Command]. The default value is
45 sec.
3.
Press the [* Clear] key to return to
the Prog Acc’nts submenu.
5.4.6 PROG FORMATS
The PROG FORMATS feature allows you to
program the reporting formats and codes
used by the D9068 in reporting 4/2
formats.
To program reporting formats and codes:
At the Programming Menu, press [6] to
enter the PROG FORMATS submenu. The
window shows:
PROG FORMATS
1: 4/2 POINT RPT
2: 4/2 RPT CODES
3: SIA SILENC RPT
The following sections include format
programming information.
1: 4/2 POINT RPT
To access
4/2 POINT RPT
, select
[0]:
PROGRAM
[6]: PROG FORMATS
[1]: 4/2
POINT RPT
. The 4/2 Reports consist of an
event type (first digit) and a point
number (second digit). These reports
apply to points, and only when 4/2
format is selected. Refer to
for more information.
