16
B O S C H
* Model dependent
EN
G
L
ISH
2. If the cloth is synthetic, it may melt due to the
high temperature on the soleplate, switch off
the steam and rub off any residue immediately
with a thickly folded, dry cotton cloth.
3. To keep the soleplate smooth, you should
avoid hard contact with metal objects. Never
use a scouring pad, or chemicals to clean the
soleplate.
AntiCalc
multiple descaling system
See the lealet sides
A
self-clean
Each time you use the steam regulator (3), the
“self-clean” system cleans the mechanism of
scale deposits.
B
Calc’nClean
The “Calc’nClean” function helps to remove
scale particles out of the steam chamber. Use
this function approximately every 2 weeks if the
water in your area is very hard.
1
Unplug the iron from the mains socket, set
the steam regulator (3) to the
position and
ill the water tank (11) with water.
2
Set the temperature control (12) to the “max”
position and plug in the iron.
3
After the necessary warm-up period, the lamp
goes out. Then, unplug the iron
(very
important!)
.
4
Set steam regulator to the “max” position.
5
Hold the iron over a sink. Press the “clean”
button (10) and shake the iron until
approximately one third of the water capacity
of the tank is evaporated. Boiling water and
steam will come out, carrying scale or
deposits that might be there.
6
Release the “clean” button, and gently shake
the iron for some seconds.
7
Repeat the steps 5 and 6 three times until the
tank is empty.
8
Then plug the iron in and heat it up again until
the remaining water has evaporated.
9
Unplug the iron and let the soleplate (7) cool
down. Wipe the soleplate with a damp cotton
cloth only.
C
“Calc’nClean” with descaling liquid *
For deep descaling, it is recommended to use
the descaling liquid especially developed by
Bosch. This procedure should be carried out
every 3 months.
1. Fill the water tank (11) with tap water mixed
with a measure (25 ml) of the descaling luid
(17 *).
2. Then follow the procedure described above in
section “Calc’nClean” (steps 2 to 9).
The descaling liquid may be purchased from our
after-sales service or specialist shops.
Name of accessory: TDZ1101
D
anti-calc
The “anti-calc” cartridge has been designed to
reduce the build-up of scale produced during
steam ironing, helping to extend the useful life of
your iron. Nevertheless the “anti-calc” cartridge
cannot remove all of the scale that is produced
naturally over time.
TextileProtect
“TextileProtect” fabric
protector *
See the lealet sides
The fabric protector (16 *) is used for
steam-ironing delicate garments at maximum
temperature without damaging them.
The fabric protector may be purchased from our
after-sales service or specialist shops.
Name of accessory: TDZ1550
StoreProtect
“StoreProtect” *
The “StoreProtect” accessory (18 *) enables
an immediate and safe storage of the iron,
even with a hot soleplate (7).
This accessory may be purchased from our
after-sales service or specialist shops.
Name of accessory: TDZ1750
Summary of Contents for DA50 SensorSecure
