background image

6 720 818 731 (2016/07)

Tronic 4000 T | Tronic 6000 T

4 | Technical properties and dimension's

appliance. Cleaning and user maintenance 
shall not be made by children without 
supervision.”

“If the power cable is damaged, it must be 
replaced by the manufacturer, its customer 
service department or a similarly qualified 
person, so that risks are avoided.”

2

Technical properties and dimension's

2.1

Determined use

DHW cylinders are designed for heating and storing potable 
water. Please observe national, regional, and local codes, 
regulations, guidelines and standards for potable water.

Any other use is considered inappropriate. We take no 
responsibility for damage caused through incorrect use.

The service life of the device strongly depends on using water 
with appropriate properties.

2.2

Type overview

[ES]

Electrical domestic hot water cylinder

[035]

Cylinder capacity (liters)

[5]

Version

[1200 W] Performance

[BO]

Make

[H1, M1] Design
[X]

Standard diameter

[C]

Capillary temperature controller

[T]

Thermometers

[W]

Wall-mounted installation

[V]

Vertical installation

[R]

Reversible installation

[B]

Connections to the bottom side

2.3

Description of the DHW cylinder

Enamel-coated steel storage cylinder according to 
European standards

High pressure stability

Outer wall jacket: Sheet-metal and/or plastic

Easy operation

CFC-free PU insulation

Magnesium anode

2.4

Corrosion protection

The internal wall of the DHW cylinder is enamel-coated. This 
provides fully neutral and water-compatible contact with 
possible water. As an additional corrosion protection measure, 
a magnesium anode is installed.

2.5

accessories

Fig. 1

[1] Screws (2x)

1)

[2] Rawl plug (2x)

1)

[3] Pressure relief valve (8 bar)

1)

[4] Isolation fitting (2x)

1)

Requirements for 
potable water

Units

Water hardness, min.

ppm
grain/US gallon
°dH

120
7.2
6.7

pH, min. – max.

6.5 – 9.5

Conductivity, min. – max.

μS/cm

130 – 1500

Table 2

Requirements for potable water

ES

035 5 1200 W BO H1 X

C

T

W

V

B

ES

050 5 1600 W

1500 W

BO H1

M1

X

C

T

W

R
V

B

ES

080 5 2000 W BO H1

M1

X

C

T

W

R
V

B

ES

100 5 2000 W BO H1

M1

X

C

T

W

R
V

B

ES

120 5 2000 W BO H1

M1

X

C

T

W

R
V

B

ES

150 5 2400 W

2000 W

BO H1

M1

X

C

T

W

R
V

B

Table 3

1) Only some models

6720801526-01.2V

3

1

2

4

Summary of Contents for ES 035 5 Series

















Reviews: