English |
15
Bosch Power Tools
1 609 92A 0MA | (10.7.14)
To remove the battery
7
, press the battery unlocking button
6
and pull the battery upward out of the power tool.
Do not ex-
ert any force.
Battery Charge-control Indication (see figure A)
The three green LEDs of the battery charge-control indicator
10
indicate the charge condition of the battery
7
. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button
9
to indicate the charge condition. This is also
possible when the battery
7
is removed.
When no LED lights up after pushing button
9
, then the bat-
tery is defective and must be replaced.
Mounting the Grinding Tools (see figure B)
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Only use properly fitting and undamaged open-end
spanners (see “Technical Data”).
– Clean the grinder spindle
3
and all parts to be mounted.
– Hold the grinder spindle
3
with open-end spanner
11
by
the spanner flats.
Loosen the clamping nut
2
with open-end spanner
12
by
applying it to the spanner flats and turning in anticlockwise
direction.
– Insert the clamping shaft of the grinding tool to the stop in-
to the collet chuck
1
.
– Hold the grinder spindle
3
firmly with open-end spanner
11
and clamp the tool bit with open-end spanner
12
by the
spanner flats, turning in clockwise direction.
The grinding tools must run completely concentrical. Do not
continue to use out-of-round grinding accessories, instead,
replace before continuing to work.
Do not tighten the collet chuck of the clamping nut as
long as no grinding accessory is mounted.
Otherwise,
the collet chuck can become damaged.
Only use grinding points with a matching shank diame-
ter.
A grinding point/accessory with a shank diameter that
does not fit the tool holder (see “Technical Data”), can not
be clamped properly and will damage the collet chuck.
The application tool must be clamped at least 10 mm.
The inner shank dimension L
0
can be used to calculate the
maximum permitted speed of the application tool from the
specifications provided by manufacturer of the application
tool. It must not be less than the maximum speed of the
power tool.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
Prevent dust accumulation at the workplace.
Dusts can
easily ignite.
Operation
Starting Operation
Inserting the battery
Use only original Bosch lithium-ion batteries with the
voltage listed on the nameplate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Insert the charged battery
7
into the base of the power tool
until the battery is securely locked.
Switching On and Off
To
start
the power tool, push the On/Off switch
5
forwards.
To
lock
the On/Off switch
5
, press the On/Off switch
5
down
at the front until it latches.
To
switch off
the power tool, release the On/Off switch
5
or,
if it is locked, briefly push down the back of the On/Off switch
5
and then release it.
To save energy, only switch the power tool on when using it.
Restarting Protection
The restarting protection feature prevents uncontrolled re-
starting of the machine after an interruption in the power sup-
ply.
To
restart the operation
, switch the On/Off switch
5
to the
Off position and start the machine again.
Note:
When switching off and on again very quickly, it is pos-
sible that the restarting protection is triggered; this will pre-
vent the power tool from starting, although the On/Off switch
5
is actuated. Set the On/Off switch
5
to the off position, and
then switch the power tool on again.
Working Advice
Optimum grinding results are achieved when the grinding tool
is moved uniformly back and forth with light pressure. Pres-
sure that is too strong reduces the performance capability of
the machine and causes the grinding tool to wear more quick-
ly.
Protect the abrasive wheels from impacts.
LED
Capacity
Continuous lighting 3 x green
≥
2/3
Continuous lighting 2 x green
≥
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
OBJ_BUCH-1461-003.book Page 15 Thursday, July 10, 2014 10:26 AM
