8
| English
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
u
Do not touch the nozzle while it is hot.
There is a risk of
burns.
Product Description and
Specifications
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The glue gun is intended for solvent-free gluing of materials
such as paper, cardboard, cork, wood, leather, textiles,
foam materials, plastic (except PE, PP, PTFE, Styrofoam®
and plasticised PVC), ceramics, porcelain, metal, glass and
stone.
Product Features
The numbering of the product features refers to the illustra-
tion of the glue gun on the graphics page.
(1)
Heat shield
(2)
Nozzle
(3)
Support bracket
(4)
Feed trigger
(5)
Charging station
a)
(6)
Mains cable
(7)
Power indicator
(8)
Glue stick
a)
a)
Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Glue gun
GKP 200 CE
Article number
0 601 950 7..
Rated power input
– Heating
W
500
– Keeping the glue gun
warm
W
30
Heat-up time
min
4
Gluing temperature
°C
200
Gluing capacity
g/min
30
Glue stick diameter
mm
11
Glue stick length
mm
45−200
Weight according to
EPTA‑Procedure 01:2014
kg
0.40
Protection class
/
Ⅱ
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Operation
Starting Operation
u
Pay attention to the mains voltage!
The voltage of the
power source must match the voltage specified on the
rating plate of the glue gun.
Switching On and Off
To
switch on
the glue gun, plug the mains plug into a plug
socket.
Allow the glue gun to heat up for approx. 7 min before start-
ing work. To do this, set the glue gun down on the support
bracket
(3)
.
To
switch off
the glue gun, remove the mains plug from the
plug socket.
u
Safely place the glue gun down after use and let it cool
completely before packing it away.
The hot nozzle can
cause damage.
Continuous Operation
The glue gun can be operated continuously when the mains
plug is plugged in. The power indicator
(7)
must light up.
During breaks from work, set the glue gun down on the unfol-
ded support bracket
(3)
.
Cable-Free Operation
It is possible to work without cables in conjunction with the
charging station
(5)
(accessory).
If the discharged adhesive becomes more viscous, heat up
the glue gun again in the charging station.
Working Advice
u
Keep people and animals away from the hot adhesive
and the nozzle tip.
Adhesive and nozzle tip will heat up to
approx. 200 °C, posing a risk of burns. If hot adhesive
comes into contact with skin, immediately hold the af-
fected area under a stream of cold water for several
minutes. Do not try to remove the hot adhesive from the
skin.
Only use adhesives that have been recommended by the
manufacturer of the glue gun and that are suitable for the
processing temperature.
Adhesive bonds can become unstuck when they are affected
by moisture or heat.
u
Remove the mains plug for longer work breaks.
The glue gun can also be used when it is switched off after
heating using the heat accumulator. If the discharged adhes-
ive becomes more viscous, plug the mains plug back into the
plug socket.
Preparing for gluing
The bonding locations must be clean, dry and free from
grease.
The materials to be glued together and the work surface
must not be easily ignited or flammable.
Test whether heat-sensitive materials are suitable before-
hand on a sample workpiece.
1 609 92A 87T | (15.09.2022)
Bosch Power Tools
