12
| English
1 609 92A 008 | (17.1.13)
Bosch Power Tools
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 17.01.2013
Assembly
Battery Charging
Use only the battery chargers listed on the graphics
page.
Only these battery chargers are matched to the lith-
ium ion battery used in your machine.
Note:
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
9
indicate the charge condition of the battery
6
. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
– To indicate the charge condition, press and hold button
8
of the switched off machine.
Removing the battery (see figure A)
– To remove the battery
6
, press the unlocking buttons
7
and
pull the battery out of the machine to the rear.
Do not ex-
ert any force.
Changing the Tool (see figures B1
–
B2)
The blade can become warm during operation. Before
removing, allow the blade to cool down.
– Loosen knurled screw
1
and set blade guard
3
to the upper
position.
– Rotate the blade
10
with a screwdriver until one of the
holes in the blade is free (uncovered).
– Insert a thin, sturdy object (e.g., a nail) into the free hole,
to block the blade.
– Unscrew the blade screw
11
.
– Remove the object with which you blocked the blade.
– Slightly lift off the blade and pull it out towards the bottom.
– Attach the new blade onto the tool holder ensuring that the
ground edge of the blade faces you.
Pay attention that the blade engages onto the tool holder.
– Tighten the blade screw again.
– Adjust blade guard
3
to the material thickness to be cut
and tighten knurled screw
1
again.
Operation
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Starting Operation
Inserting the battery
Use only original Bosch lithium ion batteries with the
voltage listed on the nameplate of your power tool.
Us-
ing other batteries can lead to injuries and pose a fire haz-
ard.
Note:
Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
– Insert the charged battery
6
into the handle until it can be
felt to engage and faces flush against the handle.
Dr. Egbert Schneider
Senior Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
LED
Capacity
Continuous lighting 3 x green
≥
2/3
Continuous lighting 2 x green
≥
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
OBJ_BUCH-1417-002.book Page 12 Thursday, January 17, 2013 2:17 PM
