16
| English
Battery charge-control indicator
The battery charge-control indicator indicates the charge
condition of the battery continuously when the On/Off
switch is pressed.
LED
Capacity
Continuous lighting, green
≥ 35 %
Flashing light, green
15 − 35 %
Flashing light, red
5 − 15 %
Continuous lighting, red
≤ 5 %
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
u
Avoid dust accumulation at the workplace.
Dust can
easily ignite.
Troubleshooting
Problem
Possible Cause
Corrective Measure
Power tool fails to op-
erate
Battery discharged
Recharge battery; also see “Battery Charging”
Power tool defective
Contact Service Agent.
Internal wiring of garden tool defective
Contact Service Agent.
Power tool functions
intermittently
On/Off switch defective
Contact Service Agent.
Excessive vibrations/
noise
Power tool defective
Contact Service Agent.
Sawing time per bat-
tery charge too low
Blade holder area needs cleaning
Hold the tool to point to the ground and start to
operate
Saw blade worn
Change saw blade
Poor sawing technique
see "Working Advice"
Battery not fully charged
Recharge battery; also see “Battery Charging”
The saw blade is run-
ning slow
Battery is getting discharged
Recharge battery; also see “Battery Charging”
On/Off switch is not fully pressed
Fully press On/Off switch
Overloaded during operation
Reduce pressing force of tool against branch
Green and red LED
flash alternately
Battery temperature is out of charging range
Increase or reduce the battery temperature to
within the specified range between 0 °C and 40
°C.
Red LED flashes 1x
Battery voltage is too low, battery is empty
Recharge battery; also see “Battery Charging”
Red LED flashes 2x
Battery temperature is out of operating range
Increase or reduce the battery temperature to
within the specified range between -15 °C and
+65 °C.
Red LED flashes fast 5x Overload (jammed blade)
Reduce pressing force of tool against branch
Operate tool before the blade touches the branch
F 016 L81 917 | (09.01.2020)
Bosch Power Tools
Summary of Contents for Keo
