21
en
Preparation
Settings
r
Instantaneous switching
at maximum speed. Hold down
switch for required duration.
0/off
Stop / Switch off
min
–
max
Operating speed steplessly
adjustable from low to high
speed.
Pulse
Intermittent operation at maximum
speed. Recommended for making
e.g. milkshakes in the blender.
Cable storage compartment
X
Fig.
C
The appliance is equipped with a cable
storage compartment. The length of the
power cord can be adjusted as required by
pulling out or pushing it back. After finishing
work, push the power cord into the cable
storage compartment by jerking it back in.
Preparation
■
Place the base unit on a flat, clean and
stable surface.
■
Pull the power cord out to the required
length.
W
Risk of injury!
–
Do not insert the mains plug until
all preparations for working with the
appliance are complete.
–
While operating the appliance, never
reach into the bowl or filling shaft.
–
After switching off, the drive continues
running for a short time. Change
tools / accessories only once the drive is
at a standstill.
Important!
–
Do not switch the appliance on until
tools or accessories have been
completely attached.
–
The appliance cannot be switched on
unless the bowl has been inserted
correctly and closed with the lid. The lid
lug must be fully inserted in the slot of
the bowl handle.
–
Only use the rotary switch to switch the
appliance on and off.
Use of tools
W
Risk of injury!
While operating the appliance, never reach
into the bowl or filling shaft with your hands.
Do not insert any objects (e.g. wooden
spoon) into the bowl or filling shaft.
Universal blade
For cutting and chopping.
W
Risk of injury!
Do not touch the sharp edges of the uni-
versal blade with bare hands. When not
in use, always store the universal blade in
the blade guard. Take hold of the universal
blade by the edge of the plastic handle only.
Kneading hook (plastic)
For kneading dough and mixing
in ingredients which are not to be cut up
(e.g. raisins, chocolate chips).
X
Fig.
D
1.
Attach the bowl. Observe the
marking (
.
) when doing so. Rotate the
bowl clockwise as far as possible.
2.
Press drive shaft 1 into the tool holder
until it locks into position.
3.
Place the tool holder with the drive shaft
on the drive. Place the universal blade
or kneading hook on the tool holder and
release.
Caution!
Do not add ingredients until tools have been
fitted.
4.
Add ingredients.
5.
Attach the lid with the pusher. Observe
the marking (
.
) when doing so.
6.
Rotate the lid clockwise as far as
possible.
7.
Insert the mains plug. Set the rotary
switch to the desired setting.
Adding more ingredients
8.
To add more ingredients, set the rotary
switch to
P
. Remove the pusher
and add ingredients through the filling
opening.
■
Add liquids through the pusher.
The pusher insert can be used as a
measuring jug.
Summary of Contents for MultiTalent 8
