background image

3

9

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

I

M

P

O

R

T

A

N

T

 

S

A

F

E

T

Y

 

I

N

S

R

E

A

D

 

A

N

D

 

S

A

V

E

 

T

H

E

S

E

 

I

N

S

T

R

U

C

T

I

O

N

S

IMPORTANT - SAVE THESE INSTRUCTIONS FOR THE 

LOCAL ELECTRICAL INSPECTOR'S USE.
LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE 

AFTER INSTALLATION IS COMPLETE.

WARNING

If the information in this manual is not followed exactly, 

fire or shock may result causing property damage or 

personal injury.

WARNING

Do not repair, replace or remove any part of the 

appliance unless specifically recommended in the 

manuals. Improper installation, service or maintenance 

can cause injury or property damage. Refer to this 

manual for guidance. All other servicing should be done 

by a qualified technician.

State of California Proposition 65 

Warnings

WARNING

This product contains chemicals known to the State of 

California to cause cancer, birth defects or other 

reproductive harm.

Appliance Handling Safety

Hidden surfaces may have sharp edges. Use caution 

when reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with the latest version of one or 

more of the following standards:

UL 858 - Household Electric Ranges

CAN/CSA-E335-1/3E-94 - Safety of Household and 

Similar Electrical Appliances - General

CAN/CSA-E60335-2-6-01 - Safety of Household and 

Similar Electric Appliances - and particular 

requirements for stationary cooking ranges, hobs, 

ovens and similar appliances.

It is the responsibility of the owner and the installer to 

determine if additional requirements and/or standards 

apply to specific installations.

Electric Safety

WARNING

Before you plug in an electrical cord or turn on power 

supply, make sure all controls are in the OFF position.

If required by the National Electrical Code (or Canadian 

Electrical Code), this appliance must be installed on a 

separate branch circuit.
The circuit breaker should have a contact separation of 

at least 3 mm on all poles.
Be sure your appliance is properly installed and 

grounded by a qualified technician. Installation, electrical 

connections and grounding must comply with all 

applicable codes.
Before installing, turn power OFF at the service panel. 

Lock service panel to prevent power from being turned 

ON accidentally.
Installer – show the owner the location of the circuit 

breaker or fuse. Mark it for easy reference.

Related Equipment Safety

The appliance is only guaranteed safe to use if installed 

by a specialist in accordance with these installation 

instructions. The installer is liable for any damage 

resulting from incorrect installation.
Remove all tape and packaging before using the 

appliance. Destroy the packaging after unpacking the 

appliance. Never allow children to play with packaging 

material. 
Never modify or alter the construction of the appliance. 
To eliminate the risk of burns or fire by reaching over 

heated surface units, cabinet storage space located 

above the surface units should be avoided. If cabinet 

storage is to be provided, the risk can be reduced by 

installing a hood that projects horizontally a minimum of 

5 inches (127 mm) beyond the bottom of the cabinet.
Verify that cabinets above the cooktop are a maximum of 

13" (330 mm) deep. 
Do not install refrigerators, dishwasher, non-fan-assisted 

ovens or washing machines which fit underneath the 

cooktop.

Note:  

We strongly recommend the installation of a 

ventilation system with this appliance.

Summary of Contents for NET5466SC

















Reviews: