background image

F 002 DG9 A00

2013-04-16

Bosch Limited

Maintenance  |  N�� ����  |  �5

N�� ����  |  �5

  |  �5

en

A00_13

Fig. 8: 

Opening the safety valve on the nitrogen tank

1  Safety valve

 

!

Ensure that you tighten the safety valve of the tank 
after releasing the pressure. If the safety valve is 
not tightened, the nitrogen filled into the tank will 
escape and the operating pressure of 10 bar will not 
be achieved.

3. 

Loosen the hose clip that fastens the filling nozzle to 
the braided hose.

4. 

Disconnect the filling nozzle from the braided hose.

5. 

Connect the new filling nozzle connector.

6. 

Place the hose clip and tighten the screws.

 

i

Ensure that the orientation of the air filling connec-
tor is in the correct position. To check, connect the 
filling nozzle to a tire. If the braided twists, repeat 
the above procedure and adjust the position of the 
air filling connector.

7. 

Maintenance

Do not carry out any maintenance work that is not spe-
cifically recommended in this chapter. Non-compliance 
invalidates warranty.

7.� 

Spare and wearing parts

Description

Order number

Filling nozzle

F 002 DG1 A23

Braided hose for outlet

F 002 DG1 A24

Vacuum pump oil 

>)

F 002 DG6 401

>) Offered only for vacuum pump

7.2 

Replacement of spare parts

7.2.� 

Replacing the air filling connector

1. 

Switch off the master switch of the NTI 1000.

2. 

Open the front door.

Risk of injury due to pressure in the hoses

High pressure in the hoses might cause the 
hoses to fly apart and cause injury.

 

Ensure that the pressure of the nitrogen 
tank is less than 2 bar before replace-
ment. 

 

i

To reduce the pressure, open the safety valve of the 
nitrogen tank till the pressure drops to 2 bar. 

 

i

To open the safety valve (Fig. 8, Pos. 1), rotate the 
valve in the anticlockwise direction.

Summary of Contents for NTI 1000





















Reviews: