background image

F 002 DG9 A00

2013-04-16

Bosch Limited

Commissioning  |  N�� ����  |  9

N�� ����  |  9

  |  9

en

4.2 

�nstallation

Requirement for installation:

 

R

Pneumatic supply - Pressure input of 10 bar to  
16 bar.

 

R

Power supply - 230 VAC +/- 10 %, single phase, 50 
Hz

4.2.� 

Preparing to install the N�� ����

The NTI 1000 unit has to be installed on a level surface 
of area 800 mm X 800 mm with concrete flooring. 

 

i

For safe operation, provide a minimum clearance of 
1000 mm around the NTI 1000.

1. 

Fix four M12 bolts to the foundation (Refer chapter 9 
for the dimensions of the NTI 1000).

2. 

Position the NTI 1000 such that the holes in the base 
align with the foundation bolts.

3. 

Fasten the M12 nuts tightly.

 

!

Cover the NTI 1000 such that it is not exposed to 
rain.

 

!

Do not apply any cleaning agents to the display 
(Fig. 1, Pos. 3), keypad (Fig. 1, Pos. 4) or the LEDs 
(Fig. 1, Pos. 9, 10) on the door (Fig. 1, Pos. 6).

4. 

Clean the surface of the NTI 1000 cabinet with a 
weak solution of detergent using a soft cloth.

4.2.2 

Mounting the vacuum pump (optional)

A00_5

1

3

4

2

Fig. 4: 

Mounting the vacuum pump

1  Vacuum pump
2  Sight glass
3  Bracket
4  3/2 solenoid valve

1. 

Open the front door of the NTI 1000.

2. 

Fasten the bracket (Fig. 4, Pos. 3) to the cabinet.

3. 

Fasten the vacuum pump (Fig. 4, Pos. 1) to the 
bracket.

4. 

Fasten the 3/2 solenoid valve (Fig. 4, Pos. 4) to the 
cabinet.

5. 

Open the protective guard covering the electrical 
components on the rear of the door.

 

i

Refer to the electrical and pneumatic diagrams to 
execute the following steps.

6. 

Connect the wiring harness from the connector X12 
of the main board to the vacuum pump.

7. 

Close the protective guard.

8. 

Connect the wiring harness from the solenoid valve 
to pin 1 on terminal block 2.

9. 

Connect the hose from the inlet of the vacuum pump 
to the outlet of the 3/2 solenoid valve.

10. 

Connect the hose from the output of manifold valve 
to the inlet of the 3/2 solenoid valve

Summary of Contents for NTI 1000





















Reviews: