Bosch PKM8DV1 Series, Instruction Manual

Imp

ort

Ap

plia

nce

s.c

om

THE EASIEST WAY TO SELF-IMPORT APPLIANCES DIRECT FROM EUROPE.

en

    Hood connection

18

Refer to the Home Connect documents supplied and 

the Home Connect section for more information. 

~

 "Home Connect" on page 13

Connecting appliances directly

If the appliance is connected directly to an extractor 

hood, the extractor hood can be controlled via the hob. 

It is then not possible for either of the appliances to 

connect to your home network or to the app. Both 

appliances can be controlled via the control panel.

Connecting appliances via your home network

Use this type of connection if neither or one of the two 

appliances is connected to the Home Connect app.
If the appliances are connected to each other via your 

home network, you can use both the hood controls and 

Home Connect to operate the hob.

Notes

■

Make sure you follow the safety instructions in the 

instruction manual for your extractor hood and that 

these are complied with even when operating the 

appliance via the hood controls on the 

hob.

~

 "Important safety information" on page 4

■

If the appliance is being operated by means of the 

controls on the extractor hood, this mode of 

operation always has priority. It is not possible to use 

the hood controls on the hob during this time.

■

In networked standby mode, your appliance requires 

a maximum of 2 W.

Setting up

To set up the connection between the hob and the 

extractor hood, the hob must be switched on.

Connecting directly

Make sure that the extractor hood is switched off.
For more information, refer to the section entitled 

"Connecting to the hob" in the instruction manual for 

your extractor hood.

Note: 

If you connect your hob directly to the extractor 

hood, it can no longer be connected to your home 

network as well and you can no longer use Home 

Connect.

1.

Touch and hold the 

t

 symbol for four seconds.

The product information is displayed.

2.

Touch the 

t

 symbol repeatedly until 

™

 and 

‚‡

 are 

displayed alternately.

‹

 lights up in the hotplate display.

3.

Set the value 

‚

 in the settings area.

‚

 flashes in the hotplate display.

4.

You have two minutes to initiate the connection 

process on the extractor hood.

Once the hob is connected to the extractor hood, the 

value 

„

 appears in the hotplate display. After you exit 

the settings menu, the symbols for the hob-based hood 

controls are displayed in the hob's control panel.

Connecting via your home network

You require a router that has WPS functionality.
You require access to your router.If you do not have 

this, follow the steps for "Direct connection".
When you begin, make sure that the extractor hood is 

connected to the app or is on your home network.

1.

Touch the 

t

 symbol for 4 seconds.

The product information will be displayed.

2.

Touch the 

t

 symbol repeatedly until 

™

 and 

‚‡

 are 

displayed alternately.

‹

 (not connected) or 

ƒ

 (connected to home 

network) will be lit on the hotplate display.

3.

Set the value 

‚

 in the settings area.

‚

 will flash on the hotplate display.

4.

If the appliance is not yet connected to your home 

network, press the WPS button on the router within 

the next 2 minutes.

The hob will be connected to your home network 

and the value 

ƒ

 will appear on the hotplate display. 

The process of connecting to the extractor hood 

starts automatically and is active for 2 minutes.

If the appliance is already connected to your home 

network, proceed to the next step.

5.

Initiate the process for connecting to the extractor 

hood.

Once the connection process is complete, the value 

„

will appear on the hotplate display.The symbols for the 

hood controls on the hob are displayed on the hob's 

control panel.