English |
25
Bosch Power Tools
1 609 929 S76 | (21.7.09)
POF 1400 ACE:
The lamp slowly goes out.
Note:
For safety reasons, the On/Off switch
22
cannot be locked; it must remain pressed during
the entire operation.
Constant Electronic Control (POF 1400 ACE)
Constant electronic control holds the speed
constant at no-load and under load, and ensures
uniform working performance.
Adjusting the Depth-of-cut
(see figure D)
f
The adjustment of the depth-of-cut may on-
ly be carried out when the router is
switched off.
For coarse adjustment of the depth-of-cut, pro-
ceed as follows:
– Place the machine with the router bit mount-
ed on the workpiece to be machined.
–
POF 1400 ACE:
– Set the fine-adjustment path to the centre
position with the adjustment knob
18
. For
this, turn the adjustment knob
18
until the
marks
19
match as shown in the figure. After-
wards, set the scale
17
to “0”.
– Set the step buffer
9
to the lowest position;
the step buffer engages noticeably.
–
POF 1200 AE:
Screw the adjusting screws
for the step buffer
24
halfway in or out.
– Loosen the wing bolt for the depth stop
11
so that the depth stop
13
can be moved free-
ly.
– Push the clamping lever for locking of routing
depth
16
in rotation direction
n
and and
slowly lower the plunge router until the rout-
er bit
21
touches the surface of the work-
piece. Let go of the clamping lever
16
again
to lock this plunging depth.
If required, push the clamping lever
16
in ro-
tation direction
o
to lock it in place.
– Push the depth stop
13
downward until it
rests on the step buffer
9
. Set the slide with
the index mark
12
to the “0” position on the
scale for the depth-of-cut adjustment
14
.
– Set the depth stop
13
to the required depth-
of-cut and tighten the wing bolt for the depth
stop
11
. Pay attention not to misadjust the
slide with the index mark
12
again.
– Push the clamping lever
16
in rotation direc-
tion
n
and guide the router to the uppermost
position.
For deep cuts, it is recommended to carry out
several cuts, each with little material removal.
By using the step buffer
9
, the cutting process
can be divided into several steps. For this, ad-
just the desired depth-of-cut with the lowest
step of the step buffer and select the higher
steps first for the initial cuts.
POF 1200 AE:
The clearance of the steps can be
changed by screwing the adjusting screws
24
further in or out.
Fine Adjustment of the Depth-of-cut
(POF 1400 ACE)
After a trial cut, the depth-of-cut can be set ex-
actly to the desired measure by turning the ad-
justment knob
18
; turn in clockwise direction to
increase the cutting depth and in anticlockwise
direction to decrease the cutting depth. The
scale
17
can be used for guidance. One full turn
corresponds with a setting range of 2.0 mm; a
graduation mark on the top edge of the scale
17
corresponds with a 0.1 mm change of the set-
ting range. The maximum setting range is
±
8 mm.
Example:
The desired depth-of-cut is to be
10.0 mm; the trial cut resulted in a cutting depth
of 9.6 mm.
– Lift up the router and place, e. g., a piece of
scrap wood under the guide plate
7
so that
the router bit
21
cannot touch the workpiece
when lowering it. Push clamping lever
16
in
rotation direction
n
and slowly lower the
plunge router until the depth stop
13
faces
against the step buffer
9
.
19
OBJ_BUCH-323-003.book Page 25 Tuesday, July 21, 2009 12:51 PM
Summary of Contents for POF 1200 AE
Page 3: ... 3 Bosch Power Tools 1 609 929 S76 21 7 09 F E D C B A 26 21 25 27 16 14 13 12 11 9 28 29 3 5 ...
Page 4: ...1 609 929 S76 21 7 09 Bosch Power Tools 4 L K J I H G 31 33 32 31 34 31 30 4 ...
Page 5: ... 5 Bosch Power Tools 1 609 929 S76 21 7 09 P O N M 40 36 35 37 38 39 41 42 35 43 20 7 43 ...
