English |
11
Battery model ProCORE18V...
LEDs
Capacity
5× continuous green light
80−100 %
4× continuous green light
60−80 %
3× continuous green light
40−60 %
2× continuous green light
20−40 %
1× continuous green light
5−20 %
1× flashing green light
0−5 %
Fitting Protective Equipment
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
Note:
If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard
(8)
onto the holder on the
power tool until the coding
cams of the protective guard
are aligned with the holder.
When doing so, press and
hold the unlocking lever
(1)
.
Press the protective guard
(8)
onto the spindle collar un-
til the shoulder of the pro-
tective guard is sitting on the
flange of the power tool and
rotate the protective guard
until it audibly clicks into
place.
Adjust the position of the protective guard
(8)
to meet the
requirements of the operation. To do this, push the unlock-
ing lever
(1)
upward and rotate the protective guard
(8)
into
the required position.
u
Always position the protective guard
(8)
such that the
two cams on the unlocking lever
(1)
engage in the
corresponding openings on the protective guard
(8).
u
Adjust the protective guard
(8)
such that sparking in
the direction of the operator is prevented.
u
The protective guard
(8)
must only be adjustable
while the unlocking lever (1)
is actuated. Otherwise,
the power tool must not be used any more under any
circumstances and must be sent to the after-sales ser-
vice.
Note:
The coding cams on the protective guard
(8)
ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
u
Always use the protective guard for cutting (10) when
cutting with bonded abrasives.
u
Provide sufficient dust extraction when cutting stone.
The protective guard for cutting
(10)
is fitted in the same
way as the protective guard for grinding
(8)
.
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block
(20)
is fit-
ted in the same way as the protective guard for grinding
(8)
.
Side handle
u
Do not operate your power tool without the side
handle
(7)
.
Screw the side handle
(7)
on the left or right of the machine
head depending on how your are working.
Low-vibration auxiliary handle
The low-vibration auxiliary
handle reduces vibration,
enabling the tool to be used
safely and more comfort-
ably.
u
Do not make any alterations of any kind to the auxili-
ary handle.
Do not continue to use a damaged auxiliary handle.
Hand guard
u
Always fit the hand guard (14)
when working with the
rubber sanding plate
(15)
or with the cup brush/disc
brush/flap disc.
Attach the hand guard
(14)
to the side handle
(7)
.
Fitting and removing abrasive tools
Follow the special assembly instructions for
X-LOCK application tools.
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
Do not touch grinding and cutting discs until they have
cooled down.
The discs can become very hot while work-
ing.
u
Only use original X-LOCK application tools that carry the
X-LOCK logo. A maintained clamping gauge of max.
1.6 mm can only be guaranteed with original X-LOCK ap-
plication tools. A higher clamping gauge can lead to insec-
ure clamping, potentially causing the clamp tool to come
loose.
u
X-LOCK application tools do not need additional clamping
flanges or support flanges.
u
Make sure that the application tool and the holder are not
deformed and are free from dirt and particles.
Bosch Power Tools
1 609 92A 6CZ | (14.07.2021)
Summary of Contents for Professional GWX 180-LI
