English |
25
requirements of the operation. To do this, push the unlock-
ing lever
(1)
upward and rotate the protective guard
(10)
into the required position.
u
Always position the protective guard
(10)
such that
the two cams on the unlocking lever
(1)
engage in the
corresponding openings on the protective guard
(10).
u
Adjust the protective guard
(10)
such that sparking in
the direction of the operator is prevented.
u
The protective guard
(10)
must only be adjustable
while the unlocking lever (1)
is actuated. Otherwise,
the power tool must not be used any more under any
circumstances and must be sent to the after-sales ser-
vice.
Note:
The coding cams on the protective guard
(10)
ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
u
For cutting, always use the protective guard for
cutting
(11)
or the protective guard for grinding
(10)
together with the cover for cutting (14)
.
u
Provide sufficient dust extraction when cutting stone.
The protective guard for cutting
(11)
is fitted in the same
way as the protective guard for grinding
(10)
.
Metal cover for cutting
Fit the metal cover for cutting
(14)
on the protective guard
for grinding
(10)
(see figure
A
): Swivel the tool retainer back
(
➊
). Attach the cover
(14)
to the protective guard for
grinding
(10)
(
➋
). Press the tool retainer firmly into place
on the protective guard
(10)
(
➌
).
To remove the cover (see figure
B
), press the button on the
tool retainer (
➊
) and swivel it back (
➋
). Remove the
cover
(14)
from the protective guard
(10)
(
➌
).
Plastic cover for cutting
Attach the plastic cover for cutting
(14)
to the protective
guard for grinding
(10)
(see figure
C
). The cover
(14)
aud-
ibly and visually engages on the protective guard
(10)
.
To remove the cover (see figure
D
), unlock the cover
(14)
on
the left- or right-hand side of the protective guard
(10)
(
➊
)
and remove the cover (
➋
).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block
(26)
is fit-
ted in the same way as the protective guard for grinding
(10)
.
Hand guard
u
Always fit the hand guard (19)
when working with the
rubber sanding pad
(20)
or with the cup brush/conical
brush/diamond annular cutter.
Attach the hand guard
(19)
to the auxiliary handle
(8)/(9)
.
Standard auxiliary handle/low-vibration auxiliary handle
Screw the auxiliary handle
(8)/(9)
on the right or left of the
machine head depending on the working method.
u
Do not operate your power tool without the auxiliary
handle (8)/(9)
.
u
Do not continue to use the power tool if the auxiliary
handle (8)/(9) is damaged. Do not make any altera-
tions to the auxiliary handle
(8)/(9).
The low-vibration auxiliary
handle
(9)
reduces vibra-
tion, enabling the tool to be
used safely and more com-
fortably.
Fitting and removing abrasive tools
Follow the special assembly instructions for
X-LOCK application tools.
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
Do not touch grinding and cutting discs until they have
cooled down.
The discs can become very hot while work-
ing.
u
Only use original X-LOCK application tools that carry the
X-LOCK logo. A maintained clamping gauge of max.
1.6 mm can only be guaranteed with original X-LOCK ap-
plication tools. A higher clamping gauge can lead to insec-
ure clamping, potentially causing the clamp tool to come
loose.
u
X-LOCK application tools do not need additional clamping
flanges or support flanges.
u
Make sure that the application tool and the holder are not
deformed and are free from dirt and particles.
Pay attention to the dimensions of the abrasive tools.
Make sure that
both
X-LOCK catches are open (see figure
below) before fitting the X-LOCK application tool.
If necessary, clean the area between the two X-LOCK
catches.
Fitting the abrasive tool
➊
Place the grinding/cutting/flap disc in a central position
on the X-LOCK holder, parallel to the bearing surface
and with the right side facing up.
➋
Push the disc into the holder.
➌
The disc audibly clicks into place. Do not actuate the
lever
(3)
when doing so.
Bosch Power Tools
1 609 92A 76B | (16.02.2022)
Summary of Contents for Professional GWX 18V-8
