background image

6 720 606 990 (2014/06)

Remote Control

Remote control installation for: GWH C920 ES/GWH C920ESC /GWH C800 ES/GWH 

5

Remote control installation for: GWH C920 ES/GWH C920ESC /GWH C800 ES/GWH 715 
ES/ GWH 2700 ES/GWH2400ES/EVOLUTION500/INTEGRA500/C1210ES/C1210ESC/
C1050ES/C950ES/940ES/940ESO/830ES

5.1

Remote control transceiver PCB installation

WARNING: 

For safety reasons, disconnect 

the power supply to the water heater before 
performing installation.

Pre-installation preparation

▶ Loosen the two Philips head screws located on bottom rear 

of cover.

▶ Lift front cover upward and remove.
▶ Remove the three screws from the control unit (Fig. 8, 

[1]).

Fig. 7

 

 

▶ Remove the 6 screws from the back cover of the control 

unit, to access the electronic board (PCB) (Fig. 8, [2]).

6720606990-10.1AL

Fig. 8

 

 

Remote control transceiver PCB installation

▶ Place the remote control PCB in the back cover of the 

control unit as shown in Fig. 9.

Fig. 9

 

 

 

▶ Connect the supplied cable between the main PCB and the 

remote control PCB as shown in Fig. 10.

Fig. 10

 

 

 

▶ Reassemble all parts in the reverse order.

Summary of Contents for Remote Control













Reviews: