background image

3.6 

Protection Against Electric Shock (PELV) by Protective Extra-

Low Voltage

All connections and terminals on Rexroth products with voltages of 5 to 50 volt

are protective extra low voltages, made to protect against contact in accordance

with the following standards:

WARNING

High electric voltage by incorrect connection! Risk of death or bodily

injury by electric shock!

Only devices, electrical components and lines with a Protective Extra Low

Voltage (PELV) may be connected to any connections or terminals with

voltages of 0 to 50 volt.

Only connect voltages and circuits that have safe isolation from dangerous

voltages. Safe isolation can be achieved, for example, by isolating trans‐

formers, safe opto-electronic couplers or mains-free battery operation.

3.7 

Protection Against Dangerous Movements

Dangerous movements can be caused by faulty control of connected motors.

Some common examples are:

improper or wrong wiring of cable connections

incorrect operation of the equipment components

wrong input of parameters before operation

malfunction of sensors, encoders and monitoring devices

defective components

software or firmware errors

These errors can occur immediately after equipment is switched on or even

after an unspecified time of trouble-free operation.
The monitoring in the drive components will normally be sufficient to avoid faulty

operation in the connected drives. Where personnel safety is concerned, par‐

ticularly where there is a risk of physical injury and/or damage to property, this

fact should not be relied on exclusively. Until the integrated monitoring functions

become effective, it must be assumed in any case that faulty drive movements

will occur. The extent of faulty drive movements depends upon the type of con‐

trol and the state of operation.

Project Planning Manual | Rexroth IndraControl VAU 01.1Z

 Electric Drives

and Controls

| Bosch Rexroth AG

11/45

Safety Instructions for Electric Drives and Controls

Summary of Contents for Rexroth IndraControl VAU 01.1Z

















































Reviews: