background image

16

/84

Bosch Rexroth AG

LTU350/1  |    3 609 929 B47/2008-12

Table of Contents

About this document  . . . . . . . . . . . . . . . . . 17

General safety instructions  . . . . . . . . . . . . 17

Delivery contents  . . . . . . . . . . . . . . . . . . . . 19

Product description  . . . . . . . . . . . . . . . . . . 20

Transport and storage  . . . . . . . . . . . . . . . . 24

Assembly   . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Commissioning   . . . . . . . . . . . . . . . . . . . . . 25

Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Maintenance and repair . . . . . . . . . . . . . . . 25

Decommissioning   . . . . . . . . . . . . . . . . . . . 25

Disassembly and replacement  . . . . . . . . . 26

Disposal  . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Extension and conversion  . . . . . . . . . . . . . 26

Troubleshooting  . . . . . . . . . . . . . . . . . . . . . 26

Technical data  . . . . . . . . . . . . . . . . . . . . . . 27

Service and sales . . . . . . . . . . . . . . . . . . . . 28

The data specified above only serves to 
describe the product. No statements 
concerning a certain condition or suitability 
for a certain application can be derived from 
our information. The information given does 
not release the user from the obligation of 
own judgment and verification. It must be 
remembered that our products are subject to 
a natural process of wear and aging.

 

This document, as well as the data, 

specifications, and other information set forth 
in it, are the exclusive property of Bosch 
Rexroth AG. It may not be reproduced or 
given to third parties without its consent.

This document was written in German.

LTU350.book  Page 16  Tuesday, December 16, 2008  12:24 PM

Summary of Contents for Rexroth LTU350/1














Reviews: