background image

3 609 929 B47/2008-12  |  LTU350/1

Bosch Rexroth AG

19

/84

ENGLISH

ENGLISH

ITALIANO

ESPAÑOL

PORTUGUÊS

SVENSKA

FRANÇAIS

Observe the regulations for accident 
prevention and environmental protection for 
the country where the product is used and at 
the workplace.
Exclusively use Rexroth products in good 
technical order and condition. 

Check the product for visible defects, for 
example damage to the circuit board, 
components, housing, and plug connectors 
or missing screws.

Only use the product within the performance 
range provided in the technical data.

Persons who assemble, operate, 
disassemble or maintain Rexroth products 
must not consume any alcohol, drugs or 
pharmaceuticals that may affect their ability 
to respond.

The warranty only applies to the delivered 
configuration. 

The warranty will not apply if the product is 
incorrectly assembled or handled or not used 
as intended.

Do not expose the product to any mechanical 
loads under any circumstances. Never use 
the product as a handle or step. Do not place 
any objects on it.

During assembly

Make sure the relevant system component is 
not under pressure or voltage before 
assembling the product or when connecting 
and disconnecting plugs. Protect the system 
against being switched on.

Lay cables and lines so that they cannot be 
damaged, are in accordance with the 
bending radiuses, and no one can trip over 
them.

Before commissioning, make sure that all the 
connection gaskets and plugs are installed 
correctly to ensure that they are leakproof 
and fluids and foreign bodies are prevented 
from penetrating the product.

During commissioning

Let the product acclimate itself for several 
hours before commissioning, otherwise 
water may condense in the housing.

Make sure that all electrical connections are 
either used or covered. Commission the 
product only if it is installed completely.

During cleaning

Cover all openings with the appropriate 
protective equipment in order to prevent 
detergents from penetrating the system.

Never use solvents or aggressive detergents. 
Only clean the product using a slightly damp, 
lint-free cloth. Only use water to do this and, 
if necessary, a mild detergent.

Disposal

Dispose of the product in accordance with 
the currently applicable national regulations 
in your country. 

3

Delivery contents

The delivery contents include:

• 1 LTU350/1 servo amplifier
• 1 operating instructions for the servo 

amplifier

LTU350.book  Page 19  Tuesday, December 16, 2008  12:24 PM

Summary of Contents for Rexroth LTU350/1














Reviews: