15
BOSCH
ENG
lISH
7
Multiple descaling
system
Depending on the model, this range is equipped
with the “AntiCalc” (=component 1 + 2 + 3).
1. self-clean
Each time you use the steam regulator, the
“self-clean” system cleans the mechanism of
scale deposits.
2. calc’n clean
The “calc‘n clean” function helps to remove scale
particles out of the steam chamber. Use this
function approximately every 2 weeks, if the
water in your area is very hard.
1. Unplug the iron from the mains socket, set the
steam regulator to the position and fill the
water tank with water.
2. Set the temperature selector to the “max”
position and plug in the iron.
3. After the necessary warm-up period, the lamp
goes out.
Then, unplug the iron (very
important!).
4. Hold the iron over a sink. Press the “clean”
button until approximately one third of the water
capacity of the tank is evaporated. Boiling
water and steam will come out, carrying scale
or deposits that might be there.
5. Release the “clean” button, and gently shake
the iron for some seconds,
6. Repeat the steps 4 and 5 three times until the
tank is empty. Then plug the iron in and heat it
up again until the remaining water has
evaporated.
7. Unplug the iron and let the soleplate cool down.
Wipe the soleplate with a damp cotton cloth
only.
3. anti-calc
The “anti-calc” cartridge has been designed to
reduce the build-up of scale produced during
steam ironing, helping to extend the useful life of
your iron. Nevertheless the “anti-calc” cartridge
cannot remove all of the scale that is produced
naturally over time.
8
“secure” auto shut-off
function
(Model dependent)
The "secure" auto shut-off function switches off
the iron when it is left unattended, thus increasing
security and saving energy. After plugging in the
appliance, this function will be inactive for the first
two minutes in order to give the appliance time to
reach the set temperature.
Alter such time, if the iron is not moved for 8
minutes while in the upright position or 30
seconds while resting on its soleplate or on its
side, then the safety circuit will switch the
appliance off automatically and the pilot light will
start flashing.
To reconnect the iron, just move it about gently.
9
anti-drip system
(Model dependent)
If the temperature is set too low, the steam is
automatically switched off to avoid dripping.
10
Fabric protection
soleplate cover
(Model dependent)
The fabric-protection is used for steam-ironing
delicate garments at maximum temperature
without damaging them.
Use of the protector also does away with the
need for a cloth to prevent shine on dark
materials.
It is advisable to first iron a small section on the
inside of the garment to see if it is suitable.
To attach the fabric protector to the iron, place
the tip of the iron into the end of the fabric
protector and press the rear of the protector
upward until you hear a click. To release the
fabric protector, pull down on the clip at the rear
and remove the iron.
The fabric-protection soleplate cover may be
purchased from the customer service or specialist
shops:
Accessory code
(After-sales)
Name of accessory
Protect cover soleplate
464851
TDZ1510
Summary of Contents for sensixx B7
