Bosch SGE63E06UC - Evolution 24" Special Application Dishwasher FR, Operating Instructions Manual

Problem

Cause

Action

Dishwasher 

does not start

1.  Door may not be properly latched.

2.  Unit may not be turned on.

3.  Unit not reset or previous cycle not completed.

4.  Delay start engaged.

5.  Interruption of electrical power supply to dishwash-

er or blown fuse.

6.  Child lock activated (select models).

7.  The door may have been closed without first select-

ing a cycle.

8.  Water supply may not be turned on.

1.  Shut the door completely.
2.  Press the main power switch to turn unit on.
3.  To reset, refer to “Canceling or changing the cycle” section in this 

manual.

4.  To reset, refer to “Delay Start” section in this manual.
5.  Check circuit breaker.
6.  Deactivate  the  child  lock.  Refer  to  “Child  Lock”  section  in  this 

manual if applicable.

7.  Select a cycle and close the door.
8.  Check and turn on water supply.

Dishwasher 

beeping (end 

of cycle signal)

Default factory settings alert the customer that the cycle 
has completed by beeping. This feature can be deacti-
vated if so desired.

To adjust the volume or deactivate, refer to “Cycle Completion Sig-
nal” section in this manual.

Display does 
not illuminate 
or console 
lights are not 
on

1.  A  fuse  may  have  been  blown  or  circuit  breaker 

tripped.

2.  Door not closed or latched.
Note: For models with controls on the top portion of the 
door, the display only illuminates when the door is opened and 
controls are visible. 

1.  Check the fuse or circuit breaker box and replace the fuse or re-

set the breaker if necessary.

2.  Ensure that door is properly latched and completely closed.

Dishwasher 
seems to run a 
long time

1.  Incoming water is not warm enough. 
2.  Cycle  time  can  vary  due  to  soil  and  water  condi-

tions.

3.  Rinse agent dispenser is empty.
4.  Dishwasher connected to cold water supply.

Note: Refer to “Cycle Chart Data” section in this manual 
for typical cycle length. 

1.  Before starting a cycle, run hot water faucet at the sink nearest 

to the dishwasher. 

2.  Sensors in the dishwasher automatically increase the cycle time 

to ensure a good wash when heavy soil is detected.

3.  Add rinse agent.  

4.  Verify dishwasher is connected to hot water supply plumbing.

Dishes aren’t 
getting clean 
enough

1.  Spray arm movement is obstructed.
2.  Spray arm nozzles clogged.
3.  Improper use of detergents.
4.  Filters could be clogged.
5.  Dishes are nested or loaded too close together.
6.  Selected wash cycle is not suitable for food soil 

condtions.

1.  Ensure that spray arm movement is not blocked by hand rotating 

spray arms. 

2.  Remove  the  spray  arms  and  clean  according  to  “Check/Clean 

the Spray Arm Nozzles” in Care and Maintenance section of this 

manual.

3.  Increase  or  decrease  detergent  depending  on  the  water  hard-

ness. Refer to Table under “Adding Detergent and Rinse Agent”.

4.  Clean the filter. Refer to “Check/Clean the Filter System” under 

Care and Maintenance section of this manual.

5.  Rearrange load such that water spray can reach all items in the 

dishwasher.  See  also  “Preparing  and  Loading”  section  of  this 

manual.

6.  Refer to “Wash Cycle” section in Operating the Dishwasher sec-

tion of this manual.

Dishes are not 
getting dry 
enough

1.  Rinse agent dispenser is empty. (Rinse agent indica-

tor is activated).

2.  Improper loading of dishes.
3.  Selected cycle does not include drying.
Note: Plastic or Teflon do not typically dry as  completely 
as other items due to their inherent properties.

1.  Add rinse agent. The use of rinse agent improves drying.

2.  Rearrange load to ensure items are not nested. Refer also to the 

“Preparing and Loading” section of this manual.

3.  Rinse and Hold setting does not include drying cycle,

Note: Select models offer an extra heating options to improve drying 

performance. Refer to “Wash Cycle options”  under  the Operating 

the Dishwasher section of this manual.

Odor

1.  Food  debris  is  present  at  the  bottom  of  the  dish-

washer.

2.  Food particles are present near the door seal.
3.  Dishes left too long in unit before running a cycle.
4.  Residual water is present at the bottom of the dish-

washer.

5.  Drain hose is obstructed.

1.  Remove the filters and clean according to the “Check/Clean the 

Filter System” section of this manual.

2.  Refer to “Clean the Door Gasket and Door Seal” in the Care and 

Maintenance section of this manual .

3.  Run a Rinse/Hold cycle if you do not intend to immediately wash 

the dishes.

4.  Ensure the unit has completely drained from the last cycle. Refer 

to the “Canceling or changing the cycle” section of this manual.

5.  Remove any obstructions from the drain hose by calling qualified 

personnel.

Note: If odor still persists, run the Normal/Regular cycle until it flushes 

and interrupt the cycle and place an 8 oz. cup of distilled white vinegar 

solution on the top rack and then finish the cycle.

SELF HELP

Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The following information may help you 
with a dishwasher problem without involving a repair professional.

20