background image

Detergent

 en

27

Separate detergents

Separate detergents are products
that do not contain components other
than detergent, e.g. powder deter-
gent or liquid detergent.
With powder and liquid detergent the
dosage can be individually adjusted
to the level of soiling of the table-
ware.
For better washing and drying results
and to avoid damage to the appli-
ance, please additionally use "Spe-
cial salt" → 

Page 23

 and "Rinse aid"

→ 

Page 25

.

Combined detergent

Besides conventional separate deter-
gents, a number of products are
available with additional functions.
These products contain not only de-
tergent but also rinse aid and salt re-
placement substances (3in1) and,
depending on the combination (4in1,
5in1, ...), additional components such
as glass protection or stainless steel
cleaner.
According to manufacturers, com-
bined detergents generally only func-
tion up to a water hardness of 26
 °E. With a water hardness above 26
 °E you will need to add special salt
and rinse aid. For the best washing
and drying results we recommend
using special salt and rinse aid from
a water hardness of 17 °E. If you are
using combined detergent, the wash-
ing programme is adjusted automat-
ically to ensure the best possible
washing and drying result.

Unsuitable detergents

Do not use detergent which could
cause damage to the appliance or
present a risk to health.

Detergent

Description

Hand washing-up
liquid

Hand washing-up liquid
can cause increased froth-
ing and damage the appli-
ance.

Detergent con-
taining chlorine

Chlorine residue on table-
ware may present a risk to
health.

Information on detergents

Follow the instructions on detergents
in everyday use.

¡

Detergents marked as "organic" or
"ecological" (environmentally
friendly) generally contain lower
levels of active agents or com-
pletely dispense with certain sub-
stances. The cleaning effect may
be restricted here.

¡

Set the rinse aid and the water
softening system to the separate
detergent or combined detergent
in use.

¡

According to manufacturers, com-
bined detergents with salt replace-
ment substances can only be used
up to a certain water hardness,
usually 26  °E, without adding spe-
cial salt. For the best washing and
drying results we recommend us-
ing special salt from a water hard-
ness of 17 °E.

¡

To prevent sticking, only touch de-
tergents in a water-soluble pouch
with dry hands and only ever place
them in a dry detergent dispenser.

¡

Even if the rinse aid and special
salt refill indicators light up, wash-
ing programmes will run properly
with combined detergents.

Summary of Contents for SGS2ITW41G

























































Reviews: