8
9
ADD DETERGENT
Use detergent tabs, fresh powdered detergent or liquid detergent. For the Glass
cycle, use 1 -1.75 Tbsp. of detergent or use detergent tabs with glassware
protection.
Tip: dispenser lid should slide closed easily.
1.75 Tbsp. (25 ml)
3 Tbsp. max.
1 Tbsp. (15 ml)
TO CLOSE THE COVER
CLICK
DETERGENT AMOUNTS
LAY TABS FLAT
START YOUR DISHWASHER
1.
Press the On/Off button.
2.
Select a cycle and option if desired.
3.
Press Start.
FREQUENTLY ASKED QUESTIONS
Q
:
Why is food left on dishes?
A
:
It is possible the dishes do not have adequate clearance between them.
Also, be sure nothing is blocking spray arm and that the filter is clean. Select an
intensive cleaning cycle.
Q
:
Why does the cycle run a long time?
A
:
1. Sensors in the dishwasher automatically increase the cycle time to ensure a
good wash when heavy soil is detected.
2. Incoming water may not be hot enough and dishwasher has to heat it.
Q
:
Why is E:XX (X can be any number) displayed?
A
:
This is an error code. For example E:22 indicates there is water in the sump
because the filter is blocked or needs cleaning. See the Use and Care Manual
for a list of error codes.
To access the full Use and Care Manual, go to:
www.bosch-home.com/us/service/get-support/owner-manuals.
MAINTENANCE TIPS
Clean surfaces with damp cloth and mild soap.
NOTICE:
Do not use abrasives or bleach based cleaners. Do not use stainless
steel cleaner on black stainless or anti-finger print surfaces.
Clean the filter 3-12 times a year, depending on usage.
1.
Unscrew the Large Object Trap as illustrated and remove the entire filter
system.
2.
Remove the micro-filter from the fine filter, rinse the filters under running
water clean with a soft brush.
3.
Reinstall the filter system in reverse sequence, align arrows.
1
2
ADD RINSE AID
This dishwasher is designed to be used
with rinse aid, which enhances drying
results and shine.
Tip: avoid air vent and remove lid for easier
pouring.
max
vent
air
Setting
Factory setting Description
•
Water hardness
•
:
‹‹
-
•
:
‹ˆ
•
:
‹…
Setting the water hardness.
§
-Rinse Aid
§
:
‹‹
-
§
:
‹‡
§
:
ܠ
Dispenses the amount of rinse aid,
which affects drying (see above).
š
-Intensive drying
š
:
‹‹
-
š
:
‹‚
š
:
‹‹
/ off
Improved drying for glasses and
plastic, by increasing the tempera-
ture and length.
›
-Beep at cycle end
›
:
‹‹
-
›
:
‹„
›
:
‹ƒ
Adjust the sound level of the signal
beep at the end of the cycle.
‚
-Infolight®
*
‚
:
‹‹
-
‚
:
‹‚
‚
:
‹‚
/ on
Light projected on the floor to signal
active wash cycle. Set to on or off.
˜
-Auto power off
˜
:
‹‹
-
˜
:
‹ƒ
˜
:
‹‚
/ off after
one minute
Unit turns itself off after cycle is
complete, either after 1 minute,
˜
:
‹‚
or after 2 hours,
˜
:
‹ƒ
.
†
TimeLight®
*
†
:
‹‹
,
†
:
‹‚
†
:
‹‚
/ on
While a wash cycle is running,
status information is projected onto
the floor. Set to on or off.
ADJUSTING THE SETTINGS
1.
Press the On/Off button. Hold down button
A
(see pages 6-7) and press
Start until the display shows
•
:
‹
x (x can be any number).
2.
Release both buttons. The LED for the button
A
flashes and the digital
display shows the factory set value. Press
A
to choose the setting.
3.
Press buttons
B
or
C
(up or down) to change the setting.
4.
Press Start button to save the setting.
*
Depending on the model