background image

en

Bosch Solar Module c-Si M 48 EU I Bosch Solar Module c-Si M 60 EU I Bosch Solar Module c-Si M 60 S EU I Bosch Solar Module c-Si P 60 EU     Bosch Solar Energy AG

3 Positioning guidelines

In order to achieve the highest-possible annual energy 
yield, we recommend positioning the module so as to 
fulfill the following criteria:

 

Definitely align the solar module so as to avoid a 
shadowing effect (even to a temporary or partial 
extent: e. g. due to roof dormers, trees), since this 
can lead to damage in the solar modules (e. g. forma-
tion of „hot spots“), failure of the PV generator and 
loss of output.

 

Align the front of the solar module to the south.

 

Select the angle of inclination according to the local 
and structural factors (30° ± 15°). You will find spe-
cific data on optimum module positions in the perti-
nent specialized literature. The calculation of the 
angle of inclination can be based on the following 
formula: angle of inclination = latitude of the positio-
ning locality – 20°.

 

All modules of a photovoltaic generator are to be 
aligned at the same angle (horizontal as well as verti-
cal). In the event of angle deviations, separate fre-
quency converters are to be designated.

4 | Positioning guidelines

 

In order to ensure sufficient selfcleaning, the angle of 
inclination must amount to at least 10°.

 

For optimized selfcleaning, a 15° minimum angle of 
inclination is recommended.

 

Always ensure that the reverse side of the module is 
well ventilated.

 

To avoid increased strain of the modules due to wind 
load, it is necessary to observe minimum distances 
from building boundaries according to DIN 1055-4.

 

A concentration of sunlight on the modules via mir-
rors or lenses is prohibited.

 

Avoid contact with salty water!

 

The crystalline solar modules made by Bosch Solar 
Energy have been tested in accordance with the 
following norms for their response to contact with 
salty air:

  – IEC 61701: 1995
  – DIN EN 61701: 2000-08
  – IEC 60068-2-52. 

Please observe the test conditions indicated in the 
norms when using the modules in salty air.

Summary of Contents for -Si M 60 EU30123













Reviews: