Solution 6000
Installation Manual
System Programming
11-9
Bosch Security Systems 07/14 BLCC610I
D12v O/Load
Setting this option allows the keypad to display a system
trouble message when the current load on the +12 V
terminal exceeds its maximum rating of 1Amp.
12v O/Load
Setting this option will cause the panel to send an
Overcurrent Trouble report to the base station when the
current load on the +12 V terminal exceeds its maximum
rating of 1Amp.
Display LAN O/Load
Setting this option allows the keypad to display a system
trouble message when the current load on the LAN+
terminal exceeds its maximum rating of 1Amp.
Report LAN O/Load
Setting this option will cause the panel to send an
Overcurrent Trouble report to the base station when the
current load on the LAN+ terminal exceeds its maximum
rating of 1Amp.
H O R N S P E A K E R O P T I O N S
System > Siren >
Tone
MENU 7-4-0
This menu allows you to customise the tone that is
emitted from the horn speaker when a non-fire alarm is
triggered. By changing the tone and speed, it is possible
to program a unique siren sound for each system when
you are installing a number of them in close proximity to
each other.
1)
Press [MENU] + [7] + [4] + [0]. The keypad will
display the current siren tone.
Tone
1. . . . . . . . . . . . . 7
-------------
---------
Press
OK to SAVE
2)
Use the up and down arrow keys to change the the
siren tone.
3)
To test the new siren tone press [ON] to sound the
siren and press [OFF] to turn the siren off.
4)
Repeat Steps 2 and 3 until the desired siren tone is
achieved then press [OK] to save and exit, or press
[MENU] to exit without saving.
i
Note
Only outputs programmed as Event Type 36 and or
37 will be affected by this menu option.
System > Siren >
Speed
MENU 7-4-1
This menu allows you to customise the speed of the siren
tone when a non-fire alarm is triggered. By changing the
tone and speed, it is possible to program a unique siren
sound for each system when you are installing a number
of them in close proximity to each other.
1)
Press [MENU] + [7] + [4] + [1]. The keypad will
display the current siren speed.
Speed
S. . . . . . . . . . . . . F
-------------
---------
Press
OK to SAVE
2)
Use the up and down arrow keys to change the
siren speed.
3)
To test the new siren speed press [ON] to sound the
siren and press [OFF] to turn the siren off.
4)
Repeat Steps 2 and 3 until the desired siren tone is
achieved then press [OK] to save and exit, or press
[MENU] to exit without saving.
i
Note
Only outputs programmed as event type 36 and or
37 will be affected by this menu option.
System > Siren >
Volume
-
MENU 7-4-2
(*** System Wide Parameter ***)
1 5
This menu allows you to program the volume level of the
radio key speeker beeps which are heard when the system
is armed and disarmed using a radio keyfob.
1)
Press [MENU] + [7] + [4] + [2]. The keypad will
display the current siren volume (default = 15).
Volume
15
Press 0-9 OK to SAVE
2)
Using the numeric keys, enter the new volume
level. Valid entries are 0 to 15 where 15 = the
loudest volume and 0 = no speeker beeps.
3)
Press [OK] to save and exit or press [MENU] to exit
without saving.
i
Note
Only outputs programmed as Event Type 36, horn
speaker with beeps will be effected by this menu
option.
