5
6
¥Ê ɯ
¥Ê
µ¯¯
³¤ ¤
1
üü
2
üü
c
ü
§Ê
'
a
$
Individual settings
ʑ
Signal
1.
Activate the setting mode for the signal volume
2.
a) Set the volume for
button signals(
depending on model)
2.
b) Set the volume for
information signals
Information on the display panel
depending on model
§
:
³Å
Turn the (cold water) tap on fully;
supply hose kinked/trapped;
water pressure too low; service, clean the filter
a
page 10
,
§
:
³µ
Detergent solution pump blocked; service, clean the detergent solution pump
a
page 10
.
Drainage hose/waste pipe blocked; service, clean the drainage hose at the siphon
a
page 10
.
§
:
´
Water in the base tub, appliance leaking. Turn off the tap. Call the after-sales service.
'
Childproof lock active; Deactivating
a
page 5
.
Other
displays
Switch off the appliance, wait for 5 seconds and switch it back on again. If the display
appears again, call the after-sales service
.
rpm
+
To activate the
setting mode
set to
Â
press and
hold
turn one
position to
the right
press and hold for a
further 5 secs until the
display elements light up;
setting mode is activated
rpm
set to
Â
to exit the setting
mode for the signal
volume
press repeatedly until
the desired volume is
reached
or
rpm
turn one
position to
the right
press repeatedly until the
desired volume is
reached
set to
Â
to exit the
setting mode for the
signal volume
rpm
a
a
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
a
~
ʋ
ʋ
ʋ
ʋ
~
§Ê
2
$
>
$
$
a
$
Æ
$
Individual settings
ʑ
Function buttons
The spin speed and temperature can be changed before and during the selected
programme. The effects depend on the programme progress.
Temp.°C
You can change the displayed washing temperature. The maximum washing temperature
that can be selected depends on the programme that has been set.
rpm
(spin speed //
;
(Rinse stop = no final spin))
You can change the spin speed shown or select
;
(Rinse stop (Spülstop) = no final spin,
laundry remains in the water after the last rinse, display panel - - - -). The maximum selectable
spin speed depends on the model and on which programme is currently selected.
Ready in
When you select the programme, the relevant programme duration is displayed. You can
delay the start of the programme before it begins. The "Finished in" time can be set in
increments of one hour up to a maximum of 24 hours. Press the
Ready in
button
repeatedly until the required number of hours is displayed (h = hour).
Press
Start/
Soaking
$
.
ʑ
Option buttons
a
Programme overview,
page 7
ē
Speed Wash
For washing in a shorter time with a washing result comparable to that
of the standard programme. Maximum load
a
Programme overview,
page 7.
2
Rinse Plus
Additional rinse cycle. For areas with very soft water or for further
enhancing the spin result.
º
Intensive
For saving energy with a comparable washing effect to the standard
programme.
ʑ
Childproof lock
'
on the display panel
You can lock the washing machine to prevent the functions you have
set from being changed inadvertently.
ON/OFF
: after the start/end of the programme, press and hold the
Start/Pause button for approx. 5 seconds.
Note: The childproof lock can remain activated until you wish to start
the next programme, even after switching off the machine.
Then you can deactivate the childproof lock before starting the
programme and activate it again as necessary once the programme
has started.
ʑ
Start/ Soaking
$
To start, pause and continue the programme and to activate/deactivate the childproof lock.
a
>
$
a
L
ü
7
I
7
1
ü
c
ÿ
O
2
ü
>
ü
c
6
ā
$
G
$
'
a
a
