a
ē
L
ü
¥Ê
ē
2
º
7
ā
ü
¥Ê
ē
2
º
I
¥Ê
ē
2
º
7
1
ü
¥Ê
ē
2
º
c
¥Ê
ē
2
º
G
¥Ê
ē
2
º
c
¥Ê
ē
2
º
:
O
¥Ê
Z
¥Ê
ē
2
º
c6
¥Ê
2
>
L
ü
@
L
ü
@
L
ü
@
L
ü
@
I
ü
B
1
ü
c
B
ÿü
O
B
L
º
I
$
ē
L
$
$
$
~
a
ʑ
ʑ
ʑ
a
>
c
>
$
11
What to do if...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
–
Start/
Soaking
$
not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
a
page 11.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Programme stopped?
a
page 4
.
– - - - - (Rinse stop = no final spin) selected?
a
page 3,4.
ʑ
Programme does not start. –
Start
/Soaking
$
or
Ready in
time selected?
– Washing machine door closed?
– Childproof lock active? Deactivating
a
page 5.
ʑ
Detergent solution is not
drained.
– - - - - (Rinse stop = no final spin) selected?
a
page 3, 4.
– Clean the detergent solution pump
a
page 11.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Spin result not satisfactory.
Laundry wet/too damp.
– Not a fault - the imbalance monitoring system has interrupted the spin
because the laundry is unevenly distributed.
Distribute large and small items of laundry evenly in the drum.
– Speed selected too low?
a
page 5
.
ʑ
The programme duration
changes during the wash
cycle.
– Not a fault - the programme cycle is optimised for the particular
washing process. This can cause changes in the programme duration
on the display panel.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced-load detection system is adjusting the
imbalance.
ʑ
Residual water in the
0
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
a
page 10
.
ʑ
Odour formation in the
washing machine.
– Run programme
L
Cottons 90 °C
without laundry. Use standard
detergent.
ʑ
Status display
t
flashing.
Appliance has detected a
detergent overload.
– Too much detergent used?
Mix one tablespoonful of fabric softener with ½ litre water and pour
into compartment
II
(Not for outdoor fabrics, sportswear fabrics or
those made with down.)
–
Reduce the detergent dosage for the next wash cycle
.
ʑ
Loud noises, vibrations and
“wandering” during the
spin cycle.
– Are the appliance feet fixed?
Secure appliance feet
a
Installation instructions
.
– Transportation safety devices removed?
Remove transportation safety devices
a
Installation instructions
.
ʑ
Display panel/indicator
lamps do not function
during operation.
– Power cut?
– Circuit breakers tripped? Switch the circuit breakers back on or
replace.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced-load detection system is adjusting the
imbalance by repeatedly redistributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
ʑ
There are detergent
residues on the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select
Rinse
2
or brush down the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to
Off
and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
a
Installation instructions.
Washing machine
en
Instruction manual
