background image

en

    Cleaning and maintenance

24

3.

Open and remove the service flap. 

4.

Take the drain hose out of the 

retainer.

Remove the sealing cap, allow the 

detergent solution to flow out into a 

suitable container.

Replace the sealing cap and place 

the drainage hose in the retainer.

5.

Carefully unscrew the pump cover, 

residual water may leak out.

Clean the interior, pump cover 

thread and pump housing. The 

impeller in the detergent solution 

pump must be able to rotate.

Refit the pump cover and screw it on 

tightly. The handle must be in a 

vertical position.

6.

Place the service flap back on, lock 

it into place, and close it.

Note:  

To prevent unused detergent 

from flowing straight into the drain 

during the next wash: Pour 1 litre of 

water into compartment 

II

 and start the 

[

 Empty

 programme.

The drain hose at the siphon 

is blocked

1.

Switch off the appliance. Disconnect 

the mains plug.

2.

Loosen the hose clamp. Carefully 

remove the drain hose, residual 

water may leak out. 

3.

Clean the drainage hose and siphon 

connecting piece.

4.

Reattach the drainage hose and 

secure the connection using the 

hose clamp.

Filter in the water supply 

blocked

For this, first reduce the water pressure 

in the supply hose:

1.

Turn off the water tap.

2.

Select any programme (except 

Rinse//Spin/Drain).

3.

Press 

Start

/Reload 

A

. Allow the 

programme to run for approximately 

40 seconds.

4.

Set the programme selector to 

Off

Disconnect the mains plug.

5.

Clean the filter on the water tap:

Remove the hose from the water tap.

Clean the filter with a small brush.

Summary of Contents for WAK2020SGC







































Reviews: