?
?
?
?
¢
?
I
1
:
:
ü
÷
O
:
?
¢
.
÷
$
Â
7
7
?
$
$
$
~
10
Care
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Immediately remove laundry and cleaning agent residues.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
...
if it contains detergent or fabric softener residues.
1.
Pull out the drawer up to the stop position, press down on the latch on the
insert and remove the drawer completely .
2.
Remove insert: Pull the insert upwards using your finger.
3.
Clean the detergent dispenser and the insert with water and a brush.
4.
Refit the insert and secure it in place (the cylinder should fit over the
guide pin).
5.
Insert the detergent drawer.
6.
Leave the detergent drawer open so that residual water can evaporate
.
Drum
Leave the washing machine door open after washing so that the drum can dry.
Rust stains – use chlorine–free cleaning agent, not steel wool
.
Descaling
Ensure that there is no laundry in the machine.
This is not necessary if the detergent is dispensed correctly. However, if it is necessary, follow
the instructions provided by the descaler manufacturer. Suitable descaling products can be
purchased from our website or customer service
.
a
page 13
Information on the display
Please close the door immediately due to the rising water level. In the pause
status,
and
are displayed alternately
.
The door is locked for safety reasons (water level and/or temperature are too
high); in the pause status
,
and
are displayed alternately. If you need
to open the door, wait for the temperature to drop or drain the water (e.g. select
Drain
>
programme)
.
The door cannot be locked/unlocked due to the high temperature of the door
lock. Wait a moment and try again
.
+
Flashing
(no water supply):
Tap turned on?
Inlet filter blocked? Clean the filter
.
a
page 11
Supply hose kinked or blocked
?
Flashing
: The washing machine detected the imbalance in the drum and it
cannot be adjusted. To protect the washing machine, the maximum spin speed
cannot be reached. The washing solution will not be removed completely after
spinning.
-
Wash small and large items of laundry together.
Clean the drain pump;
a
page 11
Outlet pipe/drainage hose blocked
.
Other displays
Switch off the appliance, wait 5 seconds and switch it back on.
If the display appears again, call the after-sales service
a
page 13
– Risk of electric shock.
Pull out the mains plug.
– Risk of explosion. No solvents.
11
– Risk of scalding.
Allow detergent solution to cool down.
– Turn off the tap.
Maintenance
Drain pump blocked
Set programme selector to
Â
Off
, pull out the mains plug.
1.
Open service flap.
2.
Take the drainage hose out of the holder.
3.
Remove sealing cap, allow detergent solution to flow out. Have a suitable
container ready.
Push up the closing cap and place the drain hose back in its holder.
4.
Carefully unscrew the pump cover (Caution! residual water).
Clean the interior, pump cover thread and pump housing (fan impeller
in the detergent-solution pump must rotate).
5.
Reinsert and screw on pump cover. Handle should be vertical.
6.
Close the service flap.
To prevent unused detergent from flowing into the outlet during the next
wash: Pour 1 litre of water into dispenser
II
and start the
Spin
or
Drain
>
programme.
Drainage hose on the siphon blocked
Set programme selector to
Â
Off
, pull out the mains plug.
1.
Loosen hose clip, carefully remove drainage hose (Caution! residual
water).
2.
Clean drainage hose and siphon spigot.
3.
Re-attach drainage hose and secure connection point with hose clip.
Filter blocked in water inlet hose
Risk of electric shock!
Do not immerse Aqua-Stop safety device in water (contains electric valve).
Release water pressure in the supply hose:
1.
Turn off the tap!
2.
Select any programme (except
Rinse
«
,
Spin
or
Drain
>
).
3.
Press
Start
/Reload button. Leave programme for approx. 40 seconds.
4.
Set programme selector to
Â
Off
. Pull out the mains plug.
Clean the filter:
5.
Disconnect the hose from the water tap.
Clean filter with small brush.
and/or
for standard and Aqua-Secure models:
remove hose from the rear of the appliance.
Take out filter with pliers and clean.
6.
Connect the hose and check for leaks.
ʑ
ʑ
$
a
ʑ
a
a
a
ʑ
$
ʑ
a
ʑ
ʑ
a
ʑ
ʑ
~
a
ʑ
.
ʑ
ʑ
a
ʑ
ʑ
ʑ
2
ʑ
Â
a
Â
a
ʑ
a
ʑ
ʑ
