background image

Faults and what to do about them.       

en

41

Information on the display panel

Indicator

Cause/remedy

è

 off

The door is unlocked at the end of the programme or when paused, laundry can be 

added/removed

è

 is lit up

During the programme. Door locked.

Paused: Temperature too high. Wait until the temperature drops.

Paused: Spin speed too high. Wait until the drum comes to a halt.

Paused: Water level too high. It is not possible to add laundry. Touch 

A

 to 

continue the programme.

è

 flashes

Slowly: The door cannot currently be locked or unlocked. Waiting time 

required.

Quickly: Close the door because water can flow out from the laundry.

è

 and the ActiveOx-

ygen 

Refresh 

Ø

 indicator 

light flash 

The door cannot be opened due to programme-related technical reasons.
When the lights go off, the door can be opened.

A

 off

At the end of the programme, while the door is open

A

 is lit up

After the programme has started

A

 is flashing

Before the programme starts, paused

r

 is lit up

Water pressure too low, may increase the length of the programme.

r

 is flashing

No water supply:

Turn the tap on fully,

The supply hose is kinked/trapped,

Clean the filter if necessary. 

~

 Page 39

E

 3 sec is lit up

The childproof lock is activated – deactivate it. 

~

 Page 34

E

 3 sec is flashing

The childproof lock is activated – the programme selector has been turned or the 

control panel touched.

Û

 is flashing

Run the 

Drum Clean 90 °C

 programme or a 60 °C programme to clean and care 

for the drum and the outer tub.

Notes

Run the programme without laundry.

Use standard washing powder or a detergent that contains bleach. To prevent 

foaming, only use half the amount of detergent recommended by the detergent 

manufacturer. Do not use detergents intended for woollens or delicates.

Switching the information signal on/off 

Å

 is lit up

Too much foam has been detected and additional rinse cycles have been activated. 

Add less detergent to the next wash cycle with the same load. 

Summary of Contents for WAT287H0

















































Reviews: