background image

en

    Programme default settings

30

0

Programme default 

settings

Programme default settings

Note:  

You can find possible 

programme default settings in the 

overview; these differ depending on the 

model.

The programme default settings for all 

programmes are preset at the factory 

and are displayed in the display panel 

after the programme is selected.

Temperature

(

Temperature)

Setting depending on the model
Depending on what stage the program 

is in, you can change the set 

temperature before and at the 

beginning of the program.
The maximum temperature that can be 

set depends on the program that has 

been selected.

Spin Speed

(

0

 rpm)

Depending on what stage the program 

is in, you can change the spin speed (in 

rpm; revolutions per minute) before and 

during the program. 

Setting 0

: The rinsing water is drained 

but there is no final spin. The laundry 

stays wet inside the drum, e.g. for items 

that should not be spun.

Setting

 - - - -: (Rinse Stop) = no final 

spin. The laundry stays in the water after 

the final rinse.
You can select "Rinse Stop" to prevent 

creasing if the laundry will not be taken 

out of the washing machine immediately 

after the program has ended. 

To continue/end the program 

~

 Page 36

The maximum speed that can be set 

depends on the model and program 

that has been selected.

Finish in time

(

ñ

 Finished In)

Before starting the program

, you can 

preselect the program end ("Ready in" 

time) in hourly increments (h = hour) up 

to a maximum of 24 hours.

To do this:

1.

Select a program. 

The program duration is displayed 

for the selected program, e.g. 

2:30

 

(hours:minutes).

2.

Press the 

ñ

 Finished In

 button 

repeatedly until the required number 

of hours is displayed.

3.

Press the 

A

 Start/Reload button.

The door will be locked.

The selected number of hours 

(e.g. 

8 h

) is shown in the display 

panel and counts down until the 

wash program starts. The duration of 

the program is then displayed.

During the timer count-down

, you can 

change the preselected number of 

hours as follows:

1.

Press the 

A

 Start/Reload button.

2.

Use the

 

ñ

 Finished In

 button to 

change the number of hours.

3.

Press the 

A

 Start/Reload button.

During the timer count-down

, you can 

add or remove laundry as required:

1.

Press the 

A

 Start/Reload button.

2.

Open the door and add or remove 

laundry.

3.

Close the door.

4.

Press the 

A

 Start/Reload button.

Summary of Contents for WAU28460ID

















































Reviews: