background image

en

    Cleaning and maintenance

38

2

Cleaning and 

maintenance

Cleaning and maintenance

:

Warning

Danger of death!

There is a risk of electric shock if you 

touch live components.

Switch off the appliance and unplug the 

mains plug.

:

Warning

Risk of poisoning!

Toxic vapours can be produced by 

cleaning agents that contain solvents, 

e.g. cleaning solvent.

Do not use cleaning agents that contain 

solvents.

Caution!

Damage to the appliance

Cleaning agents that contain solvents, 

e.g. cleaning solvent, can damage 

surfaces and components in the 

machine.

Do not use cleaning agents that contain 

solvents.

Machine housing/control 

panel

Wipe the housing and the control 

panel with a soft, damp cloth.

Remove the detergent residue 

immediately.

Do not clean with a water jet.

Drum

Use chlorine-free cleaning agents, do 

not use steel wool.
If there are odours in the washing 

machine, or to clean the drum, run the 

Drum Clean

 Û

 

90 °C

 or 

i

 

Cottons

 

90 °C

 program without 

laundry. Add washing 

powder.

~

 "Faults and what to do 

about them" on page 43

Descaling

Descaling should not be necessary if 

the detergent is measured out correctly. 

However, if it is required, follow the 

manufacturer's instructions for the 

descaling agent. Suitable descalers can 

be obtained via our website or from our 

after-sales service. 

~

 Page 45

Detergent drawer and housing

If the detergent drawer contains 

detergent or fabric softener residues:

1.

Pull out the detergent drawer. Press 

down the insert and fully remove the 

drawer.

2.

To remove the insert: Push the insert 

upwards from below with your finger.

3.

Clean the detergent dispenser tray 

and insert with water and a brush, 

and dry it. Clean the inside of the 

housing as well.

4.

Fit the insert and lock it in place 

(push the cylinder onto the guide 

pin).

5.

Push in the detergent drawer.

Note:  

Leave the detergent drawer open 

so that any residual water can 

evaporate.

Summary of Contents for WAU28460ID

















































Reviews: