background image

en

    Operating the appliance

22

1

Operating the 

appliance

Operating the appliance

Preparing the washing 

machine

Note:  

The washing machine 

must be 

correctly installed

 and 

connected

From 

~

 Page 36

.

1.

Connect the mains plug.

2.

Turn on the tap.

3.

Open the door.

4.

Check that the drum is completely 

drained. Drain if necessary.

Switching on the appliance/

selecting a programme

Press the 

#

 button. The appliance is 

switched on.
The 

Cottons

 programme set at the 

factory is then always displayed.
You can use this programme or select a 

different programme. The programme 

selector can be turned in either 

direction.

Note:  

If you have activated the 

childproof lock, you must deactivate it 

before you can set a different 

programme. 

~

 Page 24

The indicator light on the programme 

selector lights up and the 

default 

programme settings

 for the selected 

programme appear in the display panel:

Temperature

Spin speed

The maximum load and the duration 

of the programme (alternately)

Information on water and energy 

consumption

In appliances with a 

drum light

:

The drum is lit after switching on the 

appliance, after opening and closing the 

door and after starting the programme. 

The light switches off automatically.

Placing laundry into the drum

:

Warning

Danger of death!

Items of laundry pretreated with 

cleaning agents that contain solvents, 

e.g. stain remover/cleaning solvent, may 

cause an explosion after being loaded 

into the washing machine.

Hand-rinse these items of laundry 

thoroughly beforehand.

Notes

Mix items of laundry of varying sizes. 

Laundry items of different sizes 

distribute themselves better during 

the spin cycle. Individual laundry 

items may cause an unbalanced 

load. 

Observe the maximum specified 

load. Overfilling adversely affects the 

washing result and promotes 

creasing.

1.

Unfold presorted laundry items and 

place them in the drum.

2.

Make sure that no items of laundry 

are trapped between the door and 

the rubber seal, and close the door.

The 

A

 button indicator lamp flashes 

and the programme settings appear in 

the display panel.

Summary of Contents for WAW28540AU













































Reviews: