Bosch WAW285H1UC, Use And Care Manual / Installation Instructions

35

Optional program settings

Optional program settings 

At the factory, temperature and spin speed options, and 

cycle duration ("Finish in" time) are pre-set for all cycles.
After selection of the cycle, these values are displayed in 

the display field.

EcoPerfect™

Energy optimised washing by reducing the temperature 

while achieving a washing result that is consistent with 

the selected program, without the EcoPerfect™ setting.

Prewash

For heavily soiled washing. Pour 1/3 of normal detergent 

amount into pre-wash chamber I and remaining 2/3 into 

main wash chamber II.

Rinse Plus

This feature adds additional rinses to selected program 

which is helpful for locations with soft water supplies or 

to generally improve rinsing results. It will increase the 

program duration.

Remote Start

Briefly pressing the 

Remote Start

 button activates or 

deactivates the Remote start function. Activating the 

Remote start function enables the appliance to be started 

remotely via the Home Connect® app.

NOTICES

▯

Remote start can only be activated if the appliance 

door is closed and the appliance is connected to your 

home network.

▯

Remote start will be deactivated in the following 

circumstances:

▯

The door is opened.

▯

There is a power failure.

▯

The 

Remote Start 

button was briefly pressed again 

deactivating it.

▯

The center of the Program Selector was pressed 

switching off the appliance.

▯

Once the program has ended.

▯

Any button was pressed or the program selector 

was turned on the control panel.

Pressing and holding the 

Remote Start 

button for at least 

3 seconds enters Home Connect settings.

Finish in

The program end (Finished in) time can be set in one 

hour increments to a maximum of 24 h (hours). After 

selecting the desired washing program (at the dial) but 

before pressing the Start/Pause button, press the Finish 

in button until the desired time is displayed, e.g. 8 h. 

Press the Start/Pause button to start the washer.

NOTICE:  

The cycle duration is included in the set Finish 

in time.

Here is an example of a 1hr:30min cycle time and an 8 h 

Finish in time. 
8 h is displayed (until the Energy-saving mode activates) 

and counts down (approximately 6hr:30min) until the 

washing cycle begins (at 1hr:30min) then the cycle 

duration 1:30 is displayed and began. Total time 

approximately 8 hours. 

Spin Speed

Before and during the cycle, you can change the spin 

speed range depending on the cycle progress. 
Touch the appropriate button until the desired setting is 

displayed.

No Spin

: This option eliminates the final spin and the 

load remains saturated with the final rinse water. The 

pump is activated to remove all residual water.

~

 Program selection table; Page 33

Temperature

Before and during the cycle, you can change the default 

temperature range depending on the cycle progress. 
Press the appropriate button until the desired setting is 

displayed.
The maximum temperature range that can be set 

depends on the cycle selected.

~

 Program selection table; Page 33

SpeedPerfect®

For washing in a shorter time with a washing result 

comparable to that of the standard program. 

NOTICE:  

Do not exceed the maximum load. 

~

 Program selection table; Page 33

Stains

There are four types of stain to choose from:

The washer adjusts the average washing temperature, 

drum movement and soaking time to the specific type of 

stain. Hot or cold water, gentle or intensive washing and 

long or short soaking ensure that the wash-program 

sequence is specially adapted to each type of stain. This 

makes sure that stains are treated in the best possible 

way.

NOTICE:  

Pressing and holding the button automatically 

runs through the set values.

Ê

Oils, food based

¶

Blood

º

Red wine 

·

Grass