background image

Operating the appliance       

en

41

Adding laundry

After starting the programme, you can 

add or remove laundry if necessary.
Press the 

A

 button to do this. 

The 

A

 button indicator lamp flashes 

and the machine checks whether it is 

possible to add laundry. 

If the following appears in the display 

panel:

Both

 the - P - and 

ÿ

 symbols light 

up, it is possible to add laundry.

- P - lights up, it is not possible to 

add laundry. 

To continue the programme, press the

 

A

 button. The programme continues 

automatically.

Notes

Do not leave the door open for too 

long when adding laundry as water 

from the laundry may leak out.

For safety reasons, the door remains 

locked when the water level or 

temperature is high, or while the 

drum is turning, and it is not possible 

to add laundry during this time.

The load display is not active during 

reloading.

Changing the programme

If you have started the wrong 

programme by mistake, you can 

change the programme as follows:

1.

Press the 

A

 button.

2.

Select another programme.

3.

Press the 

A

 button. The new 

programme starts from the 

beginning.

Cancel the programme

For programmes at high temperatures:

1.

Press the 

A

 button.

2.

To cool down laundry: Select 

Rinse

.

3.

Press the 

A

 button.

For programmes at low temperatures:

1.

Press the 

A

 button.

2.

Select 

Spin

 or 

Drain

.

3.

Press the 

A

 button.

Programme end during rinse 

hold

In the display panel, 

$

 flashes, and the 

preset spin speed and remaining 

programme length are displayed for the 

selected programme.

Continue the programme by:

Pressing the 

A

 button or 

Changing the spin speed, or setting 

the programme selector to 

Drain

 

and then pressing the 

A

 button.

Programme end

- 0 - and 

ÿ

 appear in the display panel. 

The 

A

 button indicator lamp is off.

Summary of Contents for WAW325H0GC





























































Reviews: