background image

Operating the appliance       

en

39

Measure and add detergent 

and care products

Caution!

Damage to the appliance

Cleaning agents and agents for pre-

treating laundry (e.g. stain removers, 

prewash sprays, etc.) may cause 

damage if they come into contact with 

the surfaces of the washing machine. 

Do not allow these agents to come into 

contact with the surfaces of the washing 

machine. If necessary, immediately wipe 

away spray residue and other residues/

droplets with a damp cloth.

Dosing

Dose the detergents and care products 

according to:

Water hardness (ask your water 

supply company)

The manufacturer's instructions on 

the packaging

The amount of laundry

Soiling 

~

 Page 29

Filling

:

Warning

Eye/skin irritation!

Detergents and care products may 

spray out if the detergent drawer is 

opened while the machine is in 

operation.

Open the drawer carefully.

Rinse eyes/skin thoroughly if they come 

into contact with detergents or care 

products.

If accidentally swallowed, seek medical 

advice.

Note:  

Dilute viscous fabric softener and 

fabric conditioner with a little water. This 

prevents blockages in the washing 

machine's piping.

Pour the detergent and care products 

into the appropriate compartments:

1.

Pull out the detergent drawer as far 

as possible.

2.

Add detergent and/or care products.

3.

Close the detergent drawer.

Measuring aid* for liquid detergent

*depending on the model

Position the measuring aid for dosing 

the correct amount of liquid detergent:

1.

Pull out the detergent drawer. Press 

down the insert and fully remove the 

drawer.

2.

Slide the measuring aid forwards, 

fold it down and click it into place.

3.

Reinsert the drawer.

Note:  

Do not use the measuring aid for 

gel detergents and washing powder, or 

for programmes with prewash or when 

the “Ready in” time is selected.

For models without a measuring aid

pour the liquid detergent into the 

appropriate dispenser and place it in the 

drum.

Measuring aid 

A

For liquid detergent

Compartment 

II

Detergent for the main 

wash, water softener, 

bleach, stain remover

Compartment 

i

Fabric softener, liquid 

starch; 

do not exceed 

max.

Compartment 

I

Detergent for prewash

Summary of Contents for WAW325X0EG

























































Reviews: