background image

en

    Cleaning and maintenance

56

2

Cleaning and 

maintenance

Cleaning and maintenance

:

Warning

Danger of death!

There is a risk of electric shock if you 

touch live components.

Switch off the appliance and pull out the 

mains plug.

:

Warning

Risk of poisoning!

Toxic vapours can be produced by 

cleaning agents that contain solvents, 

e.g. cleaning solvent.

Do not use cleaning agents that contain 

solvents.

Caution!

Damage to the appliance

Cleaning agents that contain solvents, 

e.g. cleaning solvent, can damage 

surfaces and components in the 

machine.

Do not use cleaning agents that contain 

solvents.

Prevent detergent residue from 

building up and odours from forming 

by following these instructions:

Notes

Ensure the room in which the 

washing machine is set up is well 

ventilated.

Leave the door and detergent 

dispenser tray open slightly when 

the washing machine is not in use.

Occasionally run a wash using the 

Cottons 60 °C

 programme and 

powder detergent.

Machine housing/control 

panel

Wipe the housing and the control 

panel with a soft, damp cloth.

Remove the detergent residue 

immediately.

Do not clean with a water jet.

Drum

Use chlorine-free cleaning agents, do 

not use steel wool.
If there are odours in the washing 

machine, or to clean the drum, run the 

Drum Clean

 

90 °C

 programme without 

laundry. Add washing powder.

Descaling

Descaling should not be necessary if 

the detergent is measured out correctly. 

However, if it is required, follow the 

manufacturer's instructions for the 

descaling agent. Suitable descalers can 

be obtained via our website or from 

customer services. 

~

 Page 65

Summary of Contents for WAWH26600W





































































Reviews: