8
Care and cleaning
Dryer housing, control panel
– Wipe clean with a soft, damp cloth.
– Do not clean with a water jet.
– Remove detergent and cleaning agent residue immediately.
– During drying, water may occasionally accumulate between the window and the seal.
This does not affect the proper operation of your dryer.
Heat exchanger
The heat exchanger requires cleaning once a month,
however this varies depending on how frequently the dryer is used.
Allow the dryer to cool down and place an absorbent cloth under the maintenance flap.
Residual water may escape.
1.
Unlock the maintenance flap and open completely.
2.
Turn both locking levers towards each another.
3.
Pull out the cap.
4.
Remove the heat exchanger.
Take care not to damage the heat exchanger.
When cleaning, use water only. Do not use hard or sharp-edged objects.
5.
Rinse the heat exchanger and the cap on all sides with a jet of water to
completely remove all of the fluff.
6.
Remove any fluff from the seals on the dryer and heat exchanger.
7.
Allow to drip dry fully.
8.
First insert the heat exchanger, then the cap.
9.
Turn back both locking levers and close the
maintenance flap until it locks closed.
Moisture sensors
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure the moisture level of the laundry.
After sustained, repeated operation, a fine layer of limescale
may form on the moisture sensors.
1.
Open the door.
2.
Clean the moisture sensors with a damp sponge which has a rough
surface.
Do not use steel wool or abrasive agents!
Only when switched off!
9
Installation
– Scope of delivery: dryer, operating and installation instructions, basket for woollens
(depending on the model)
.
– Check the dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
– Do not set up in a room that is susceptible to frost.
Freezing water may cause damage.
– If in doubt, have the appliance connected by a specialist.
Setting up the dryer
– The mains plug must always be accessible.
– Ensure that the appliance is placed on a clean, level and
firm surface.
– Do not obstruct the air inlet on the dryer.
– Keep the area around the dryer clean.
– Level the dryer using the threaded feet
and a spirit level.
Never remove the threaded feet
!
For mains connection,
see Safety instructions
a
page 13.
– Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
– The mains voltage and the voltage shown on the rating plate (
a
page 10
) must be the same.
– The connected load and necessary fuse protection are specified on the rating plate.
Converting the installed load
Note the fuse protection of the socket (
10/16 Amps.).
1.
Turn the programme selector to
Off
.
2.
Press and hold the
y
Fine adjust
button.
3.
Turn the programme selector to
Cottons Cupboard Dry Plus
; wait until the recent setting
appears in the display:
¥¯
=10A or
³
=16A.
4.
Press the
y
Fine adjust
button to change the settings.
5.
Turn the programme selector to
Off
.
Frost protection / Transport
Preparation
1.
Empty the condensate container
a
page 4/11
.
2.
Select any programme using the programme selector.
3.
Press the
Start/Pause
$
button
a
condensation is pumped into the container.
4.
Wait several minutes or until the dryer stops, and then empty the condensate container
again.
5.
Turn the programme selector to
Off
.
1.
Take all accessory parts out
of the drum.
The drum must be empty.
Make sure that the air inlet
remains unobstructed
Clean and level
Do not install the dryer behind a door
or sliding door which could prevent or
obstruct the dryer door from opening.
This will prevent children from locking
themselves in and risking their lives.
2.
3.
Do not operate the dryer if
there is a risk of frost.
10
Optional accessories
(
order from the after-sales service using the order number, depending on the model)
Connection fittings for condensation outlet
The condensation is conveyed directly via a hose.
Platform
For easier loading and unloading. The basket contained in the drawer can be used
to carry the laundry.
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth
to save space. The dryer
must
be fastened to the washing machine using this connection set.
WTZ 11400: with pull-out worktop.
Technical data
Dimensions (DxWxH)
60 x 60 x 85 cm (height adjustable)
Weight
approx. 45 kg
Max. capacity
7 kg
Condensation container
4.2 l
Connection voltage
220-240 V
Connected load
2100-2800 W
Fuse protection
10 A / 16 A
Ambient temperature
5-35°C
Product number
Production number
Inside of door
The rating plate can be found on the back of the dryer.
ʠ
Drum interior light
(depending on model)
:
The drum lights up after the door is opened
and after the programme starts, and switches off automatically.
WTZ
1110
WMZ
20500
WTZ
11410
Consumption rates
(The value on the label is achieved at the maximum heat setting.)
Fabrics/programmes
Residual moisture in the
fabrics after spinning
Drying time**
Energy
consumption**
L
Cottons 7 kg
10 A
16 A
10 A
16 A
+
.
Cupboard Dry*
1400 U/min
(50%)
121 min
95 min
3.36 kWh
3.36 kWh
1000 U/min
(60%)
141 min
111 min
3.92 kWh
3.92 kWh
800 U/min
(70%)
161 min
128 min
4.48 kWh
4.48 kWh
|
I
ron Dry*
1400 U/min
(50%)
100 min
74 min
2.42 kWh
2.42 kWh
1000 U/min
(60%)
119 min
88 min
3.06 kWh
3.06 kWh
800 U/min
(70%)
140 min
100 min
3.70 kWh
3.70 kWh
#÷
Sinthetics 3.5 kg
+
.
Cupboard Dry*
800 U/min
(40%)
52 min
46 min
1.42 kWh
1.42 kWh
600 U/min
(50%)
65 min
56 min
1.74 kWh
1.74 kWh
* Programme setting for testing in accordance with applicable standard DIN EN61121.
** The values may differ from those specified, depending on the type of fabric, composition of
laundry to be dried, residual moisture in the fabric and the amount of laundry being loaded.
11
What to do if ...
Turn the programme selector to
Off
and remove the mains plug from the socket.
ʠ
The
Start/Pause
$
indicator light
does not light up.
Mains plug plugged in?
Programme selected?
Check the socket fuse.
ʠ
The display panel light and
indicator lights
(depending on
model)
go out and the
Start/
Pause
$
indicator light flashes.
Energy-saving mode is activated
a
see the separate
Energy-saving mode
instructions.
ʠ
The display panel switches off.
The appliance goes into the sleep mode after activating
Finished in
option
a
page 5
.
ʠ
The
Í
(Condensate container)
indicator light flashes.
Empty the condensate container
a
page 4
.
Press the
Start/Pause
$
button to reset the displayed
indication and then press the
Start/Pause
$
button
again to restart the appliance if necessary.
If featured, check the hose for condensation outlet.
ʠ
p
(Fluff filter/Heat exchanger)
indicator light flashes.
Clean the fluff filter
a
page 4.
Press the
Start/Pause
$
button to reset the displayed
indication and then press the
Start/Pause
$
button
again to restart the appliance if necessary.
Clean the heat exchanger
a
page 8.
ʠ
Dryer does not start.
Start/Pause
$
button selected?
Door closed?
Programme set?
After-sales service
If you cannot rectify the fault yourself (e.g. switching off/on)
a
What to do if..., page 11/12
,
please contact our after-sales service. We will always find an appropriate solution and avoid
unnecessary visits by engineers.
The contact details of your local
after-sales service
can be found in the enclosed after-sales
service directory.
–
GB
0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.)
–
IE
01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
Please provide the after-sales service the product number (E no.) and the production number
(FD) of the appliance.
Product number Production number
You can find this information:
inside the door* / in the opened service flap*
and on the rear of the appliance.
*depending on the model
Trust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest
assured that the repair will be carried out by trained service technicians using original spare
parts.
12
What to do if ...
ʠ
Programme terminates shortly
after starting.
Ambient temperature greater than 5°C?
Is the appliance loaded with the laundry?
Load too small for selected programme?/Use timed
programme
a
page 6/7.
Loaded laundry dry?
ʠ
Water is leaking out.
Make sure the dryer is level.
Clean the heat exchanger seal.
ʠ
The door opens by itself.
Push the door closed until you hear it engage.
ʠ
Creasing.
Laundry load exceeded?
Remove articles of clothing immediately after the end
of the programme, hang up and pull into shape.
Unsuitable programme selected
a
page 7.
ʠ
Drying result is not satisfactory
(laundry feels too damp).
Warm laundry feels damper than it really is.
The selected programme does not suit the load. Use
another drying programme or, in addition, select the
timed programme
a
page 7.
Use
8
+
Fine adjust
for the dryness levels
a
page 5.
Fine layer of limescale on the humidity sensors
a
Clean the moisture sensors
a
page 8
.
Programme termination, e.g. tank full, mains power
supply failure, door open or maximum drying time
reached?
ʠ
Drying time too long.
Clean the fluff filter under running water
a
page 4/11.
Insufficient supply of air
a
Ensure that air can circulate.
Air inlet possibly blocked
a
Clear inlet
a
page 9
.
Ambient temperature higher than 35°C
a
Ventilate the
room.
ʠ
One or more indicator lights are
flashing.
Clean the fluff filter and heat exchanger
a
page 4,8/11
.
Check the installation conditions
a
page 9.
Switch off, allow to cool, switch back on and restart the
programme.
ʠ
Power failure.
Remove the laundry from the dryer immediately and
spread out. This allows the heat to dissipate. Be careful
as the door, the drum and the laundry may be hot.
13
Safety instructions
Emergency
– Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use the
dryer...
– in rooms inside the house.
– to dry fabrics.
The dryer must
NEVER...
– be used for purposes other than those described above.
– be modified in terms of its technology or properties.
Hazards
– The dryer must not be used by children or persons who have not been
instructed in its use.
– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
– Remove all objects from pockets, and lighters in particular
a
Risk of explosion.
– Do not lean or sit on the door
a
Risk of tipping.
Installation
– Secure loose cables
a
Risk of tripping.
– Do not operate a dryer if there is a risk of frost.
Mains
connection
– Connect the dryer to an AC earthed socket according to specifications,
otherwise it cannot be guaranteed that the appliance is completely safe.
– The cable cross-section must be sufficient.
– Only use earth-leakage circuit breakers with the following symbol:
– The appliance plug and socket must be compatible.
– Do not use multiple plugs/connectors and/or extension cables.
– Do not touch or hold the appliance plug with wet hands
a
Risk of electric shock.
– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead
a
Risk of electric shock.
Operation
– Only load the drum with laundry.
Check the contents before you switch the dryer on.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,
grease or paint (e.g. hair styling products, nail varnish remover, stain remover,
cleaning solvent, etc.)
a
Risk of fire/explosion.
– Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer
a
Risk of explosion.
– Do not put laundry containing foamed material/rubber in the dryer
a
elastic
material may be destroyed and the dryer be damaged due to possible
deformation of the foamed material.
– When cleaning the fluff filter, make sure that no foreign material (down or
filling material) gets into the air duct opening. If necessary, clean the drum
beforehand with a vacuum cleaner. If foreign material should still get into the
air duct
a
call the after-sales service
a
Risk of fire/explosion.
– Light things, such as long hair, may be sucked into the air inlet of the dryer
a
Risk of injury.
– Switch off the dryer once the programme has ended.
– The water from condensation is not drinking water and may be contaminated
with fluff.
Defect
– Do not use the dryer if it is defective or if you suspect that it is.
Repairs must only be carried out by the after-sales service.
– Do not use the dryer if the mains cable is defective. To avoid danger, only
have the defective mains cable replaced by the after-sales service.
Spare parts
– For safety reasons, you must only use genuine spare parts and accessories.
Disposal
– Pull out the appliance plug,
then
cut off the mains cable from the appliance.
Dispose of the appliance at a municipal waste disposal site.
– Packaging: Keep all packaging out of reach of babies and children
a
Risk of suffocation.
– All materials are environmentally sound and can be reused.
Dispose of them in an environmentally-responsible manner.
Dryer
en
Instruction manual
Summary of Contents for WTB84200IL
Page 10: ...Dryer en Instruction manual ...
