background image

en

    Signal setting

28

M

 Signal setting

Signal setting

You can change the following settings:

The speed at which the washing 

machine was spun; only used if the 

anticipated drying time needs to be 

displayed more accurately,

The volume of the audible signal at 

the end of the programme,

The volume of the audible button 

signals.

You will need to activate the setting 

mode in order to change these settings.

Activating the setting mode

1.

Switch the dryer on.

2.

Select the "Cottons" programme in 

position 1 and wait for five seconds.

Setting mode is now activated. The 

symbols go out on the display panel 

and the programme duration is 

displayed.

1.

Press and hold the Start button and, 

at the same time, turn the 

programme selector clockwise to 

position 2.

2.

The 

spin speed

 is shown on the 

display.

3.

Press the "Ready in" time button or 

the drying time button to change the 

spin speed.

4.

Turn the programme selector 

clockwise to position 3.

5.

The volume for the 

audible signal at 

the end of the programme

 is shown 

on the display.

0 = off, 1 = quiet, 2 = medium,  

3 = loud, 4 = very loud

6.

Press the "Ready in" time button or 

the drying time button to change the 

volume.

7.

Turn the programme selector 

clockwise to position 4.

8.

The volume for the 

audible button 

signal

 is shown on the display.

0 = off, 1 = quiet, 2 = medium,  

3 = loud, 4 = very loud

9.

Press the "Ready in" time button or 

the drying time button to change the 

volume.

Note:  

You can select other positions 

with the programme selector; however, 

you will be unable to change these 

settings.

Finishing setting mode

 

Turn the programme selector to the 

"Off" position once you have set the 

required spin speed and the volume. 

The settings have now been saved.


Summary of Contents for WTR85V91ES





































Reviews: